Abstract:ZrB2-based 2-based ceramics typically necessitate high temperature and pressure for sintering, whereas ZrB2-SiC 2-SiC ceramics can be fabricated at 1500 degrees C using the process of reactive melt infiltration with Si. In comparison to the conventional preparation method, reactive synthesis allows for the more facile production of ultra-high temperature ceramics with fine particle size and homogeneous composition. In this work, ZrSi2, 2 , B4C, 4 C, and C were used as raw materials to prepare ZrB2-SiC 2-SiC via combination of tape casting and reactive melt infiltration herein referred to as ZBC ceramics. Control sample of ZrB2-SiC 2-SiC was also prepared using ZrB2 2 and SiC as raw materials through an identical process designated as ZS ceramics. Microscopic analysis of both ceramic groups revealed smaller and more uniformly distributed particles of the ZrB2 2 phase in ZBC ceramics compared to the larger particles in ZS ceramics. Both sets of ceramics underwent cyclic oxidation testing in the air at 1600 degrees C for a cumulative duration of 5 cycles, each cycle lasting 2 h. Analysis of the oxidation behavior showed that both ZBC ceramics and ZS ceramics developed a glassy SiO2-ZrO2 2-ZrO 2 oxide layer on their surfaces during the oxidation. This layer severed as a barrier against oxygen. In ZBC ceramics, ZrO2 2 is finely distributed in SiO2, 2 , whereas in ZS ceramics, larger ZrO2 2 particles coexist with glassy SiO2. 2 . The surface oxide layer of ZBC ceramics maintains a dense structure because the well-dispersed ZrO2 2 increases the viscosity of glassy SiO2, 2 , preventing its crystallization during the cooling. Conversely, some SiO2 2 in the oxide layer of ZS ceramics may crystallize and form a eutectic with ZrO2, 2 , leading to the formation of ZrSiO4. 4 . This leads to cracking of the oxide layer due to differences in thermal expansion coefficients, weakening its barrier effect. An analysis of the oxidation resistance shows that ZBC ceramics exhibit less increase in oxide layer thickness and mass compared to ZS ceramics, suggesting superior oxidation resistance of ZBC ceramics.

Modification of SiBCN by Zr Atom and Its Effect on Ablative Resistance of Cf/SiBCN(Zr) Composites

Thermal ablation behavior of SiBCN-Zr composites prepared by reactive spark plasma sintering

Effects of Zr and chopped C fiber on microstructure and mechanical properties of SiBCN ceramics

Ablation properties and mechanisms of BN-coated Cf-reinforced SiBCNZr ceramic composites under an oxyacetylene combustion torch

Enhanced Mechanical Properties, Thermal Shock Resistance and Ablation Resistance of Si2BC3N Ceramics with Nano ZrB2 Addition

Incorporation of BN-coated carbon fibers into ZrB2/SiBCN ceramic composites and their ablation behavior

Enhanced ablation resistance of HfB2-HfC/SiBCN ceramics under an oxyacetylene torch environment

Enhanced Mechanical Properties, Thermal Shock Resistance and Oxidation Resistance of Si2BC3N Ceramics with Zr-Al Addition

Influence of sol-gel derived ZrB2 additions on microstructure and mechanical properties of SiBCN composites

Effect of Zr on the solid sintering process of SiBCN ceramics: Diffusion couple method experiment and DFT calculation

Enhanced ablative resistance of C/C composites with densified ZrB 2 -based ceramics by incorporation of Mo as interface layer

Preparation and flame ablation/oxidation behavior of ZrB2/SiC ultra-high temperature ceramic composites

Ablation behavior of Cf/ZrC-SiC and Cf/SiC composites produced by precursor infiltration and pyrolysis combined with gaseous silicon infiltration

Fabrication and Ablation Properties of SiC Nanowires-Network Modified Carbon/Carbon–Ultrahigh Temperature Ceramics Composites

Ablation behaviour of Csf/ZrB2-SiC composites fabricated by direct ink writing and reactive melt infiltration

Enhanced Strengths and Thermal Shock Resistance of SiC-BN-10 Vol% Cf Composites Through ZrB2 Addition

Effect of HfC addition on ablation behavior of SiBCN ceramics

Microstructure and Oxidation Behavior of ZrB2-SiC 2-Sic Ceramics Fabricated by Tape Casting and Reactive Melt Infiltration

Effect of temperature-dependent nano SiC on the ablation resistance of ZrC coating

Microstructure and Thermal Shock Behavior of Sol–gel Introduced ZrB 2 Reinforced SiBCN Matrix

Synthesis of Coatings on SiC Fibers and Their Effects on Microstructure and Mechanical Properties of SiCf/SiBCN Composites