Abstract:Cu matrix composites have received increased attention in a wide industrial area because of their excellent mechanical properties and good electrical and thermal conductivity. However, the addition of general ceramic reinforcements often leads to a marked reduction in electrical conductivity for Cu matrix composites. In this study, the ZrB 2 -reinforced Cu composites have been developed to overcome this drawback since these metal borides possess relatively high electrical conductivity. The 5 wt.% ZrB 2 /Cu composites were prepared using hot-pressed sintering techniques at varying temperatures from 760 to 920°C. The influence of sintering temperature on the microstructure, relative density, and mechanical and electrical properties was examined. The results of the SEM observation show that ZrB 2 particles are seamlessly integrated into the Cu matrix for all ZrB 2 /Cu composites. The average grain size of the Cu matrix increases from 360 to 980 nm with the increase of the sintering temperature. The increase in sintering temperature also leads to the surface porosity decrease from 1.4 to 0.4%. The relative density and electric conductivity of the composites increase at the same time as the sintering temperature increases. However, microhardness increases and decreases, with a maximum value of 92 HV0.2 achieved at 840°C. The elastic modulus and nanohardness maps determined from the nanoindentation indicate that the reinforced ZrB 2 particles demonstrate the highest values for elastic modulus (340–500 GPa) and nanohardness (30–48 GPa). At the same time, the Cu matrix possesses a modulus of 100–200 GPa and nanohardness of about 10 GPa. TEM observation confirmed that the sintering temperature exhibits little influence on the interface reaction between ZrB 2 and Cu. Both sharp interface and interface with amorphous transition layer are observed. The variation of microhardness is mainly due to the strengthening of grain refinement and to the mismatch of the thermal expansion coefficients. The above results can provide further insights into the deeper understanding of the role of sintering temperature during hot-pressed sintering.

Mechanical, Wetting and Corrosion Properties of a Zr-based Amorphous Alloy Composite Consolidated by Spark Plasma Sintering

Molten Aluminum-Induced Corrosion and Wear-Resistance Properties of ZrB2-Based Cermets Improved by Sintering-Temperature Manipulation

Effect of alloying element Zr on microstructure and properties of Cu−Y2O3 composites

Corrosion Behavior of High-performance Crystalline CuCrZr/Amorphous CuZrAl Composites in NaCl Solution

Enhanced Mechanical and Electrical Properties of CuCrZr-WC Alloy Prepared by Mechanical Alloying and Spark Plasma Sintering

Mechanical, Corrosion and Wear Characteristics of Cu-Based Composites Reinforced with Zirconium Diboride Consolidated by SPS

The influence of Zr concentration on the microstructure and properties of Cu-0.6Cr-xZr alloy: High-throughput preparation and characterization study

Effect of Sintering Temperature on the Microstructure and Properties of High-Strength and Highly Conductive 5 wt.% ZrB2/Cu Composite

Corrosion Behavior of MgZnCa Bulk Amorphous Alloys Fabricated by Spark Plasma Sintering

Investigation of the electrochemical behavior of AlCoCrFeNi–ZrO2 high entropy alloy composites prepared with mechanical alloying and spark plasma sintering

Study on Microstructure and Properties of Cu-Zr Alloy Prepared by Mechanical Alloying

Spark Plasma Sintering and Mechanical Properties of ZrO2(Y2O3)–Al2O3 Composites

Fabrication of ZrCuAlNi Metallic Glassy Matrix Composite Containing ZrO2 Particles by Spark Plasma Sintering Process

A High Strength and High Conductivity Cu0.4Cr0.3Zr Alloy Prepared by Cryo-ECAP and Heat Treatment

Mg-Based Bulk Amorphous Alloy Composites Fabricated by Spark Plasma Sintering

Microstructure and High Temperature Deformation Behavior of the Mo-ZrO 2 Alloys

Microstructural evolution and thermal stability of Al–Zn–Mg–Cu–Si–Zr alloy fabricated via spark plasma sintering

Structure and Corrosion Behavior of Multiphase Intermetallic ZrCu-Based Alloys

Spark plasma sintering and mechanical properties of Al_2O_3-ZrO_2 nanocomposites

Spark Plasma Sintering Mechanisms of the Al-Zn-Mg-Cu Alloys and TiB2/Al-Zn-Mg-Cu Composites

Mechanical properties of low-temperature sintered Al2O3/3Y-TZP composites