Abstract:Homogenously doped and mixed yttria stabilized zirconia, YSZ (with 3 and 10mol% Y2O3 known as 3YSZ and 10YSZ) and NiO/10YSZ co-precipitates (nominally corresponding to 7, 12, 24, 30, 35 and 45vol.% Ni metal), were synthesized using a continuous hydrothermal flow synthesis (CHFS) system which uses a stream of superheated water at 450°C and 24.1MPa as a reaction medium to cause rapid precipitation of metal oxide nanoparticle co-precipitates from a mixed metal salt solution. All products were obtained directly from the outlet of the CHFS reactor as a slurry, which was then cleaned and freeze-dried prior to further processing. The highly crystalline nano-powdered products were characterized using a range of analytical methods, including: powder X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), Raman spectroscopy and BET surface area measurements. Spherical primary particles of 10YSZ and 3YSZ were observed under the TEM and found to be 5.0±0.8nm (range 3.2–6.3nm) and 6.2±1.4nm (range 3.3–8.4nm) in size, with measured BET surface areas of 160.6 and 241.7m2g−1, respectively. Sintering of the nano-powder co-precipitates was performed via spark plasma sintering (SPS) at 1100°C for 1min, leading to densities of ca. 98% for 10YSZ and ca. 96% for Ni/10YSZ cermets (all NiO was converted into Ni due to the reducing atmosphere of the SPS). The 24% Ni/10YSZ cermet was subjected to focused ion beam tomography, which allowed the 3D arrangement of the conducting Ni metallic network of the dense cermet to be elucidated, and showed that a complete 3D network of Ni existed throughout the dense cermet disk. Electrical conductivity tests showed that the samples exhibited higher than expected electrical conductivity (for such low metal content), e.g., the 24vol.% Ni-containing sample achieved an electrical conductivity of ∼200Scm−1 at the fuel cell operating temperature, which corresponds to an effective conductivity of ∼117Scm−1 if a porosity of 30% were to be introduced.

Effect of Yb_2O_3 Doping on Performances of 15(20Ni-Cu)/(nife_2o_4-10nio) Cermets

Influence of Yb2o3 Addition on Microstructure and Corrosion Resistance of 10Cu/(10nio-Nife2o4) Cermets

Highly conductive low nickel content nano-composite dense cermets from nano-powders made via a continuous hydrothermal synthesis route

Effect of Metallic Phase on Relative Density of NiFe_2O_4-10NiO Based Cermet for Aluminum Electrolysis

Effect of Metallic Content on Mechanical Property of Ni/(10NiO-NiFe2O4) Cermets

Effect of Y2O3 Addition on the Microstructure and Mechanical Properties of TiCN-based Cermets

Quantification of correlation between microstructure and mechanical properties of Ni–BaZrxCe0.8−xY0.1Yb0.1O3-δ (x = 0.1, 0.5) cermet anodes by image analysis

Influence of the Metal Particle Size and Sintering Process on the Electrical Resistivity of M-Zro2/30%mo Cermet

Effect of Y2O3-doping on the Electromagnetic Properties of Ni-Zn-Co Ferrite

Effects of Pre-Calcined YSZ Powders at Different Temperatures on Ni–YSZ Anodes for SOFC

Effect of Preparation Methods on the Properties of Ni-Ysz Cermets for Sofc Anodes

Densification of Ni-NiFe2O4 cermets for aluminum electrolysis

Sintering Mechanism, Microstructure Evolution and Nanomechanical Properties of Cr-added Mo2FeB2 Based Cermets

Preparation and Properties of Ce0.8Y0.2O1.9 Electrolyte

Influence of AlN addition on the microstructure, mechanical properties and oxidation characteristics of NbC-Ni cermets

Effects of CrMnFeCoNi additions on microstructure, mechanical properties and wear resistance of Ti(C,N)-based cermets

Effects of Niobium Doping on the Stability of SrCo0.2Fe0.8O3-δ Cathodes for Intermediate Temperature Solid Oxide Fuel Cells

Microstructure and Properties of Ti(C,N)-Based Cermets with AlxCoCrFeNiTi Binder

Effect of Rare Earth Y Addition on the Microstructure and Mechanical Properties of Ti(C,N)-304ss Cermets

Fabrication, microstructure evolution, and mechanical properties of Ti(C,N)-HfN-WC-Ni-Mo cermets

Microstructure and Electrical Conductivity of Ni-Ysz Cermets Prepared by Combustion Synthesis Method