Abstract:Homogenously doped and mixed yttria stabilized zirconia, YSZ (with 3 and 10mol% Y2O3 known as 3YSZ and 10YSZ) and NiO/10YSZ co-precipitates (nominally corresponding to 7, 12, 24, 30, 35 and 45vol.% Ni metal), were synthesized using a continuous hydrothermal flow synthesis (CHFS) system which uses a stream of superheated water at 450°C and 24.1MPa as a reaction medium to cause rapid precipitation of metal oxide nanoparticle co-precipitates from a mixed metal salt solution. All products were obtained directly from the outlet of the CHFS reactor as a slurry, which was then cleaned and freeze-dried prior to further processing. The highly crystalline nano-powdered products were characterized using a range of analytical methods, including: powder X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), Raman spectroscopy and BET surface area measurements. Spherical primary particles of 10YSZ and 3YSZ were observed under the TEM and found to be 5.0±0.8nm (range 3.2–6.3nm) and 6.2±1.4nm (range 3.3–8.4nm) in size, with measured BET surface areas of 160.6 and 241.7m2g−1, respectively. Sintering of the nano-powder co-precipitates was performed via spark plasma sintering (SPS) at 1100°C for 1min, leading to densities of ca. 98% for 10YSZ and ca. 96% for Ni/10YSZ cermets (all NiO was converted into Ni due to the reducing atmosphere of the SPS). The 24% Ni/10YSZ cermet was subjected to focused ion beam tomography, which allowed the 3D arrangement of the conducting Ni metallic network of the dense cermet to be elucidated, and showed that a complete 3D network of Ni existed throughout the dense cermet disk. Electrical conductivity tests showed that the samples exhibited higher than expected electrical conductivity (for such low metal content), e.g., the 24vol.% Ni-containing sample achieved an electrical conductivity of ∼200Scm−1 at the fuel cell operating temperature, which corresponds to an effective conductivity of ∼117Scm−1 if a porosity of 30% were to be introduced.

Quantification of correlation between microstructure and mechanical properties of Ni–BaZrxCe0.8−xY0.1Yb0.1O3-δ (x = 0.1, 0.5) cermet anodes by image analysis

Microstructure and Mechanical Properties of Ni/10 Mol% Sc2O3–1 Mol% CeO2–ZrO2 Cermet Anode for Solid Oxide Fuel Cells

Effect of Yb_2O_3 Doping on Performances of 15(20Ni-Cu)/(nife_2o_4-10nio) Cermets

Influence of the Metal Particle Size and Sintering Process on the Electrical Resistivity of M-Zro2/30%mo Cermet

Highly conductive low nickel content nano-composite dense cermets from nano-powders made via a continuous hydrothermal synthesis route

Influence of Triple Sintering Additives (Bao-Cuo-b2o3) on the Sintering Behavior and Conductivity of the Proton-Conducting BaZr0.1Ce0.7Y0.2O3−δ Electrolyte Sintered at 1150 °C

Effect of Metallic Content on Mechanical Property of Ni/(10NiO-NiFe2O4) Cermets

The Microstructural Reconstruction of Variously Sintered Ni-SDC Cermets Using Focused Ion Beam Scanning Electron Microscopy Nanotomography

Enhanced Electrochemical Performance of Ba0.5Sr0.5Co0.8Fe0.2O3-δ Cathode by Zr4+, Sm3+ and Yb3+ Tri-Doped BaCeO3 Compositing for Intermediate-Temperature Thin-Film Fuel Cells

Effect of NiO Addition on the Sintering and Electrochemical Properties of BaCe0.55Zr0.35Y0.1O3-δ Proton-Conducting Ceramic Electrolyte

Interphase Mechanical Behaviors of Nickel/yttria-Stabilized Zirconia Cermets: A Study by Nanoindentation and Molecular Dynamics Simulations

Microstructure and Properties of Ti(C,N)-Based Cermets with AlxCoCrFeNiTi Binder

Effects of Pre-Calcined YSZ Powders at Different Temperatures on Ni–YSZ Anodes for SOFC

Influence of Yb2o3 Addition on Microstructure and Corrosion Resistance of 10Cu/(10nio-Nife2o4) Cermets

Sr-Yb Co-doping of BaCe0.4Zr0.6O3 Proton-Conducting Electrolyte for Solid Oxide Fuel Cells

Effects of Co-Doped Barium Cerate Additive on Morphology, Conductivity and Electrochemical Properties of Samarium Doped Ceria Electrolyte for Intermediate Temperature Solid Oxide Fuel Cells

Sintering Mechanism, Microstructure Evolution and Nanomechanical Properties of Cr-added Mo2FeB2 Based Cermets

Effect of Mo Content on In-Situ Anisometric Grains Growth and Mechanical Properties of Mo2FeB2-Based Cermets

Microstructure and Properties of Porous Ni50Cr50- Al2O3 Cermet Support for Solid Oxide Fuel Cells

Sintering behavior of BaCe<sub>0.7</sub>Zr<sub>0.1</sub>Y<sub>0.2</sub>O<sub>3-</sub> electrolyte at 1150 C with the utilization of CuO and Bi<sub>2</sub>O<sub>3</sub> as sintering aids and its electrical performance

Correlation Between Microstructure and Young’s Modulus of Porous Ceramics Using Three-Dimensional Mesoscale Analysis and FIB-SEM Reconstruction Method