Abstract:Cu matrix composites have received increased attention in a wide industrial area because of their excellent mechanical properties and good electrical and thermal conductivity. However, the addition of general ceramic reinforcements often leads to a marked reduction in electrical conductivity for Cu matrix composites. In this study, the ZrB 2 -reinforced Cu composites have been developed to overcome this drawback since these metal borides possess relatively high electrical conductivity. The 5 wt.% ZrB 2 /Cu composites were prepared using hot-pressed sintering techniques at varying temperatures from 760 to 920°C. The influence of sintering temperature on the microstructure, relative density, and mechanical and electrical properties was examined. The results of the SEM observation show that ZrB 2 particles are seamlessly integrated into the Cu matrix for all ZrB 2 /Cu composites. The average grain size of the Cu matrix increases from 360 to 980 nm with the increase of the sintering temperature. The increase in sintering temperature also leads to the surface porosity decrease from 1.4 to 0.4%. The relative density and electric conductivity of the composites increase at the same time as the sintering temperature increases. However, microhardness increases and decreases, with a maximum value of 92 HV0.2 achieved at 840°C. The elastic modulus and nanohardness maps determined from the nanoindentation indicate that the reinforced ZrB 2 particles demonstrate the highest values for elastic modulus (340–500 GPa) and nanohardness (30–48 GPa). At the same time, the Cu matrix possesses a modulus of 100–200 GPa and nanohardness of about 10 GPa. TEM observation confirmed that the sintering temperature exhibits little influence on the interface reaction between ZrB 2 and Cu. Both sharp interface and interface with amorphous transition layer are observed. The variation of microhardness is mainly due to the strengthening of grain refinement and to the mismatch of the thermal expansion coefficients. The above results can provide further insights into the deeper understanding of the role of sintering temperature during hot-pressed sintering.

Influence of the Metal Particle Size and Sintering Process on the Electrical Resistivity of M-Zro2/30%mo Cermet

Preparation of Mo25ZrB2 Cermet by Hot Pressing Sintering and Its Static Oxidation Behavior

Highly conductive low nickel content nano-composite dense cermets from nano-powders made via a continuous hydrothermal synthesis route

Influence of ZrO_2 Additives on Properties of Mo-Al_2O_3 Cermets

The Corrosion of 30% Mo-ZrO2 Cermet in Molten Slag of CaO-MgO-Al2O3

Effect of synthetic Mo2FeB2 powder on the microstructure and mechanical properties of Mo2FeB2-based cermets

Tuning microstructure for superb mechanical properties in a Ti(C,N)-(WMoTaNbTi)C-Ni/Co cermets via change sintering temperature

Study on Mechanical Properties of Hot Pressing Sintered Mullite-Zro2 Composites with Finite Element Method

Preparation and Mechanical Properties of ZrB2-based Ceramics Using MoSi2 As Sintering Aids

Electrical Conductivity of Mixed Conductors (Yo<sub>1.5</sub>)<sub>x</sub>-(Ceo<sub>2</sub>)<sub>y</sub>-(zro<sub>2</sub>)<sub>1-x-y</sub>

Evaluation of tensile property and strengthening mechanism of Zirconia reinforced molybdenum alloy

Microstructure and mechanical properties of newly synthesized Mo(Co,Fe)B cermets

Effect of Sintering Temperature on the Microstructure and Properties of High-Strength and Highly Conductive 5 wt.% ZrB2/Cu Composite

Hydrothermal synthesis of (ZrO2)0.86(Sm 2O3)0.14 nano-powders and electrical properties of its sinter

Effect of chemical composition on the microstructure and mechanical properties of MoCoB based cermets

Microstructure, mechanical properties, and corrosion resistance of Mo2(Fe,Ni)B2-based cermets prepared by reaction boronizing sintering

Reaction mechanisms and properties of in situ porous Al2O3-ZrO2-mullite composites

Preparation of Cepo4 Modified Zro2 Ceramics with Different Particle Sizes and Their Mechanical Behaviors

Investigation of electrical, corporeal, ocular, and aquaphobic properties of zirconia thin-films by varying substrate temperature for high voltage insulators

Influence of Mo addition on microstructure and mechanical properties of Ti(C,N)-based cermets fabricated by in-situ carbothermal reduction of TiO2

The Propertied Of Ysz Electrolyte Sintering At 1300 Degrees Enc