Abstract:Homogenously doped and mixed yttria stabilized zirconia, YSZ (with 3 and 10mol% Y2O3 known as 3YSZ and 10YSZ) and NiO/10YSZ co-precipitates (nominally corresponding to 7, 12, 24, 30, 35 and 45vol.% Ni metal), were synthesized using a continuous hydrothermal flow synthesis (CHFS) system which uses a stream of superheated water at 450°C and 24.1MPa as a reaction medium to cause rapid precipitation of metal oxide nanoparticle co-precipitates from a mixed metal salt solution. All products were obtained directly from the outlet of the CHFS reactor as a slurry, which was then cleaned and freeze-dried prior to further processing. The highly crystalline nano-powdered products were characterized using a range of analytical methods, including: powder X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), Raman spectroscopy and BET surface area measurements. Spherical primary particles of 10YSZ and 3YSZ were observed under the TEM and found to be 5.0±0.8nm (range 3.2–6.3nm) and 6.2±1.4nm (range 3.3–8.4nm) in size, with measured BET surface areas of 160.6 and 241.7m2g−1, respectively. Sintering of the nano-powder co-precipitates was performed via spark plasma sintering (SPS) at 1100°C for 1min, leading to densities of ca. 98% for 10YSZ and ca. 96% for Ni/10YSZ cermets (all NiO was converted into Ni due to the reducing atmosphere of the SPS). The 24% Ni/10YSZ cermet was subjected to focused ion beam tomography, which allowed the 3D arrangement of the conducting Ni metallic network of the dense cermet to be elucidated, and showed that a complete 3D network of Ni existed throughout the dense cermet disk. Electrical conductivity tests showed that the samples exhibited higher than expected electrical conductivity (for such low metal content), e.g., the 24vol.% Ni-containing sample achieved an electrical conductivity of ∼200Scm−1 at the fuel cell operating temperature, which corresponds to an effective conductivity of ∼117Scm−1 if a porosity of 30% were to be introduced.

Microstructure and Electrical Conductivity of Ni-Ysz Cermets Prepared by Combustion Synthesis Method

Highly conductive low nickel content nano-composite dense cermets from nano-powders made via a continuous hydrothermal synthesis route

YSZ Thin Films Prepared by a Novel Powder Coating Process on Porous NiO-YSZ Cermet

Preparation of Ni/Ysz Materials for Sofc Anodes by Buffer-Solution Method

Preparation of Ni/YSZ for SOFC Anodes by Buffer-Solution Method

Preparation and performance of Ni-YSZ/YSZ Co-ceramic using multiple gel-tape casting

Preparation of Ni/Ysz Anode Material Using Gel-Tape Casting and Performance Analysis

Microstructure evolution and mechanical properties of 3YSZ/Ni composites with uniform phase distribution prepared by core-shell structure microspheres

Preparation of Ni–YSZ Cermet through Reduction of NiO–YSZ Ceramic for SOFC Anode

Nanocomposite Ysz-Ni Based Cermet Powders Synthesized by Complexes-Gel-Conversion Process

Preparation and SEM of Ni/Ce-YSZ Anode Materials

Urea Combustion in situ Synthesis of NiO YSZ Composite Powders for Solid Oxide Electrolysis Cells

Influence of the Metal Particle Size and Sintering Process on the Electrical Resistivity of M-Zro2/30%mo Cermet

Preparation of NiO–YSZ composite powder by a combustion method and its application for cathode of SOEC

Preparation and Properties of the NiO-YSZ/YSZ Compound Gradient Materials

Preparation of Pr0.35Nd0.35Sr0.3MnO3−δ/YSZ Composite Cathode Powders for Tubular Solid Oxide Fuel Cells by Microwave-Induced Monomer Gelation and Gel Combustion Synthesis Process

The crystal structure and morphology of NiO-YSZ composite that prepared from local zircon concentrate of Bangka Island

Porous NiO–YSZ and Ni–YSZ composites fabricated using NiO–YSZ composite nanopowders and WO3 additive

Preparation And Properties Of Nio-Coated Ysz Anodes For Solid Oxide Fuel Cells

The Properties of YSZ Electrolyte Sintering at 1300 °C

Synthesis of nanocrystalline NiCuZn ferrite powders by sol–gel auto-combustion method