Abstract:A site-specific xenon plasma focused ion beam preparation technique for microcantilever samples (1-20 µm width and 1:10 aspect ratio) is presented. The novelty of the methodology is the use of a chunk lift-out onto a clean silicon wafer to facilitate easy access of a low-cost probe type indenter which provides bending force measurement. The lift-out method allows sufficient room for the indenter and a line of sight for the electron beam to enable displacement measurement. An electroplated nanotwinned copper (NTC) was cut to a 3 × 3 × 25 µm microbeam and in situ mechanically tested using the developed technique. It demonstrated measured values of Youngs modulus of 78.7 ± 11 GPa and flow stress of 0.80 ± 0.05 GPa, which is within the ranges reported in the literature. LAY DESCRIPTION: In this paper a site specific method is present for making particularly small mechanical tests samples, of the order of 100th the size of a human hair. These small samples can then be used to determine the mechanical properties of the bulk material. Copper with a nano twinned grain structure is used as a test medium. Ion milling was used to cut the sample to shape and a micro probe was used for mechanical testing. Ion milling can cut away very small volumes of material as it accelerates ions at the surface of the sample, atomically machining the sample. Micro probes are a cost-effective small-scale load measurement devices, however, they require a large area for accessing the sample. The indenter requirements are a problem when making you samples with ion milling as ion millers are best at making small cuts. Our aim was to design a cutting strategy which reduces the amount of cutting required while allowing samples to be fabricated anywhere on the sample. We used a chunk lift out technique to remove a piece of material which is then welded to a wafer of silicon this gives sufficient space around the sample for ion milling and testing. The additional space allowed easy access for the probe. A 3 × 3 × 10 µm micro cantilever beam was cut out from copper, this beam was then bent. The force from bending and distance bent was measured and converted into Youngs modulus which is a measure of flexibility. The modulus value measured was comparable to the values reported in other papers.

Silicon Nitride Cantilever Arrays Integrated with Si Heater and Piezoelectric Sensors for SPM Data Storage Applications

Thermo-Piezoelectric Read/Write Mechanisms for Probe-Based Data Storage

Thermopiezoelectric Cantilever for Probe-Based Data Storage System

Fabrication of SiO $_{2}$ Microcantilever Using Isotropic Etching With ICP

Fabrication and Characterization of Sio2 Microcantilever for High Sensitive Moisture Sensor

A diamond-tip probe with silicon-based piezoresistive strain gauge for high-density data storage using scanning nonlinear dielectric microscopy

Scanning probe arrays for life sciences and nanobiology applications

Design of Piezoresistive Micro-Cantilever with Stress Concentration Regions

Ultra-low dissipation patterned silicon nanowire arrays for scanning probe microscopy

Characterization Of Micromachined Sensors For Nanoscale Detection

Novel technology for controlled fabrication of aperture cantilever sensors for scanning near-field optical microscopy

Integrated Piezoelectric AlN Thin Film with SU-8/PDMS Supporting Layer for Flexible Sensor Array

Design of High-Sensitivity Cantilever and Its Monolithic Integration with CMOS Circuits

Probe-Type Microforce Sensor for Mirco/Nano Experimental Mechanics

Silicon MEMS Nanomechanical Membrane Flexure Sensor With Integrated High Gauge Factor ITO

A hybrid polymer/ceramic/semiconductor fabrication platform for high-sensitivity fluid-compatible MEMS devices with sealed integrated electronics

Electric-Force Conversion Performance of Si-Based LiNbO3 Devices Based on Four Cantilever Beams

Design and Realization of New Optical Sequential Readout for Micro-cantilever Array

Focused ion beam preparation of microbeams for in situ mechanical analysis of electroplated nanotwinned copper with probe type indenters

Improvement and Application of Scanning Near Field Optical Microscope Based on A Piezoelectric Bimorph Shear Force Beam

Mechanical characterization of biocompatible thin film materials by scanning along micro-machined cantilevers for micro-/nano-system