Abstract:Industrial interest in wrought heat-treatable aluminium-lithium (Al–Li) based alloys dates back to around 1919 in Germany. However the exploitation of these alloys has historically been limited by their mechanical property anisotropy and concerns over their localized corrosion resistance and temperature stability. Recently, in the last ten years, alloy and process development has resulted in alloy compositions and thermomechanical treatments that potentially can overcome these issues. To put these developments in perspective we have reviewed the corrosion characteristics of first, second and third generation alloys with an emphasis on localized corrosion (intergranular and exfoliation) and stress corrosion cracking (SCC).Intergranular corrosion susceptibility of Al–Li–Cu and Al–Li–Cu–Mg alloys increases with copper content, and the depth of attack increases with ageing, i.e. UA<PA<OA. For alloys that contain zinc the mode of attack is less truly intergranular and more intra-granular or inter-subgranular in nature. Susceptibility to exfoliation corrosion has a similar temper dependence when assessed by conventional EXCO testing, but not following either exposure to a “real-life” outdoor marine environment or to a less aggressive test such as MASTMAASIS. In these tests there are two regimes of exfoliation susceptibility corresponding to under- and over-aged tempers, and an intermediate regime, including peak-aged tempers, with an improved resistance, i.e., UA>PA<OA.SCC initiation from smooth surfaces is rare for copper-free Al–Li alloys irrespective of temper or whether exposure is under continuous or alternate immersion conditions. For copper-containing alloys, initiation remains difficult for smooth specimens under continuous immersion conditions, but occurs readily under conditions of alternate immersion. It is likely that crack initiation is controlled by an anodic dissolution dominated process, but crack propagation may be controlled by either anodic dissolution or a hydrogen related process.Test results reviewed to date on thin plate samples show that the lower lithium content third generation Al–Li alloys, with suitable zinc and/or silver additions and thermomechanical processing can provide an acceptable resistance to localized corrosion (IGC and Exfoliation) and SCC in near to peak aged tempers. For this conclusion to apply to thicker products (>~30 mm) further analysis of corrosion test results is required.

REVIEW OF RESEARCH ON CORROSION BEHAVIOR OF Al-Li ALLOYS

Corrosion and Stress Corrosion of Aluminum–Lithium Alloys

REVIEW ON EXFOLIATION SUSCEPTIBILITY OF ALUMINIUM ALLOYS AND QUANTITATIVE MEASUREMENT METHOD

Effect of grain structures and precipitation characteristics on the corrosion behaviour of Sc-containing Al-Cu-Li alloy

Effect of aging on the mechanical properties and corrosion susceptibility of an Al-Cu-Li-Zr alloy containing Sc

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Corrosion property of Al alloys subjected to surface severe plastic deformation: a review

Review of studies on corrosion of magnesium alloys

Interesting Phenomena for Al-Zn-Mg Aluminum Alloy after Two Years of Storage: A Comparative Study on Microstructure, Mechanical Properties and Corrosion Behavior of Aluminum Alloy with Different Aging Treatments

Review of micro-scale and atomic-scale corrosion mechanisms of second phases in aluminum alloys

Investigation on the microstructural evolution and corrosion behaviors of Zn-microalloyed Al-Cu-Li alloys

Corrosion Behaviors of Selective Laser Melted Aluminum Alloys: A Review

Review on Environmentally Assisted Static and Fatigue Cracking of Al-Mg-Si-(Cu) Alloys

Microstructure and corrosion behavior of as-homogenized and as-extruded Mg−xLi−3Al−2Zn−0.5Y alloys (x=4, 8, 12)

Effect of Microstructure Evolution on Corrosion Behavior of 2195 Al-Li Alloy Friction Stir Welding Joint

Role of alloying and heat treatment on microstructure and mechanical properties of cast Al-Li alloys: A review

Corrosion Modeling of Aluminum Alloys: A Brief Review

Microstructural Evolution and Its Influence on Mechanical and Corrosion Behaviors in a High-Al/zn Containing Duplex Mg-Li Alloy after Friction Stir Processing

Corrosion Behavior of Aluminum Alloys in Different Alkaline Environments: Effect of Alloying Elements and Anodization Treatments

Research Status and Prospective Properties of the Al-Zn-Mg-Cu Series Aluminum Alloys

Corrosion resistance and mechanism of high‐entropy alloys: A review