Abstract:Considering the development of China's strategic goal of "ocean power", aluminum alloy components, such as the deck and keel used on the ship surface, face the risk of corrosion failure during long-term service. Currently, the method of preparing a film or coating on the surface of aluminum alloys is typically used to isolate the corrosive medium and effectively protect the matrix material. Among these, thermal spraying technology is widely used for the preparation of anti-corrosion coatings on the surface of aluminum alloys owing to its simple operation and because it is not limited by the size of the parts. Aluminum reference crystal materials have a high strength and hardness owing to their unique structure and excellent properties such as a low friction and corrosion resistance. Thus, they have high potential as protective coating materials on the surface of a new generation of aluminum alloys; however, the poor bonding strength and corrosion resistance in the preparation of quasicrystalline (QC) coatings limit their application. Therefore, in this study, AlCuFe and AlCuFeSc QC coatings are prepared on aluminum alloy substrates using explosive spraying technology based on the long-term service conditions of aluminum alloy parts in a marine environment to improve the corrosion resistance of aluminum alloys and increase their service life. First, the microstructures and phase structures of the powder and coating are characterized using scanning electron microscopy and X-ray diffraction. Subsequently, the binding force and corrosion resistance of the coating are analyzed using a tensile testing machine and electrochemical workstation, and the influence of the QC phase content and corrosion resistance of the coating are studied. The tests reveal that the powder and coating are composed of a I-Al65Cu20Fe15 QC phase and small amount of the beta-AlFe phase. The AlCuFe and AlCuFeSc coatings prepared by explosive spraying have a high density and demonstrate good bonding with the substrate; the bonding strengths of the coatings are determined to be 51.9 MPa and 51.2 MPa, respectively. After annealing at 700 celcius, the content of the coating QC phase increases from 49%, 38% to 93.2%, 92.5%, respectively. In addition, the corrosion resistance of the QC coating before annealing is similar to that of the substrate, and the self-corrosion current density of the annealed QC coating is only one-fifth of that of the aluminum alloy substrate. A further comparison of the surface morphologies of the coatings with different QC contents reveales that as the QC content increases, the flatness of the coating surface increases and the pore distribution decreases, which can effectively prevent the entry of corrosive media. This suggests that an increase in the QC content enhances the corrosion resistance of the coating. The salt-water static hanging test simultaneously demonstrates that no apparent corrosion area formes on the annealed coating surface after 336 h, and the aluminum oxide passivating layer that forms on the surface provides a good protection for the substrate as the content of the QC phase increases. The stability of the QC phase I improves by the introduction of the Sc element into the Al-Cu-Fe icosahedron. This study provides a new idea for the corrosion protection of aluminum alloy surfaces used in ships and a basis for the preparation and application of aluminum reference crystal coatings.

REVIEW ON EXFOLIATION SUSCEPTIBILITY OF ALUMINIUM ALLOYS AND QUANTITATIVE MEASUREMENT METHOD

REVIEW OF RESEARCH ON CORROSION BEHAVIOR OF Al-Li ALLOYS

Exfoliation Corrosion Susceptibility of 8090 Al-Li Alloy Examined by Electrochemical Impedance Spectroscopy

ELECTROCHEMICAL IMPEDANCE SPECTROSCOPY OF Al ALLOYS DURING EXFOLIATION CORROSION

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Exfoliation Corrosion of Aluminum Alloy AA7075 Examined by Electrochemical Impedance Spectroscopy

Exfoliation Corrosion Behavior of 7050-T6 Aluminum Alloy Treated with Various Quench Transfer Time

Investigation of Exfoliation Corrosion of Rolled Aa8090 Al-Li Alloy Using Electrochemical Impedance Spectroscopy

Influence of Two-Step Aging on Exfoliation Corrosion Properties of 7050 Aluminum Alloy Plate

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

Exfoliation Corrosion of Al-Li Alloy 2090-T6 in Exco Solution: A Study of Electrochemical Noise and Electrochemical Impedance Spectroscopy

Corrosion and Stress Corrosion of Aluminum–Lithium Alloys

Effect of aging on the mechanical properties and corrosion susceptibility of an Al-Cu-Li-Zr alloy containing Sc

Experimental Study on Slip Resistant Behaviours of Aluminium Alloy-Stainless Steel Faying Surfaces

Influence Mechanism of the Quasicrystalline Phase Content on the Corrosion Resistance of AlCuFe-based Coatings

INFLUENCE OF TENSILE STRESS ON EXFOLIATION CORROSION AND ELECTROCHEMICAL IMPEDANCE SPECTROSCOPY OF 7075al - ALLOY

Review on Micro-Alloying and Preparation Method of 7xxx Series Aluminum Alloys: Progresses and Prospects

Recent Progress in Testing and Characterization of Hardenability of Aluminum Alloys: A Review

Study on the Influence of Surface Treatment Process on the Corrosion Resistance of Aluminum Alloy Profile Coating

Microstructure and Corrosion Study on Friction Surfaced Aluminum Alloy Coatings over Mild Steel

Revealing the Effect of Iron Content on the Microstructure Evolution, Mechanical Properties and Corrosion Resistance of the A356-T6 Aluminum Alloys