Abstract:Strength, toughness, and stress corrosion resistance are critical properties of aluminum alloys for high-end equipment manufacturing. Unfortunately, the situation of complex alloy composition, diverse aging systems, and conflicting property relationships hinder the synchronous enhancement of three properties. Here, we proposed an interpretable machine learning design strategy for high-end aluminum alloy. The critical intrinsic factors and explicit laws of elements affecting the ultimate tensile strength (UTS), fracture toughness ( K IC ), and stress corrosion sensitivity factor (ISSRT) of alloys were excavated: The elements with large number of electrons in d-valence electron orbitals, high boiling point, and low nuclear electron distance help enhance the UTS; The elements with low density and minimized difference in first ionization energy with aluminum help improve the K IC ; The elements with high diffusion activation energy in aluminum and high corrosion potential in seawater help reduce the ISSRT. Based on the above findings, three microalloying elements of Ti, Cr, and Zr, which have the remarkable combined effect of enhancing synchronously the three properties, were selected, and a new advanced aluminum alloy Al-10.50Zn-2.31Mg-1.56Cu-0.09Ti-0.15Cr-0.10Zr was designed. The UTS, K IC, and ISSRT were 760±4MPa, 34.9±0.3MPa·m 1/2, and 13.3%±1.7%, respectively, after RRA treatment. Microstructure analysis revealed that the new alloy had almost no micron secondary phase after RRA treatment, reducing the sites for pitting and cavity formation. The addition of Ti, Cr, and Zr formed dispersoids Al 18 (Cr,Ti) 2 Mg 3 and Al 3 Zr, which contributed to the synchronous improvement of strength, toughness, and stress corrosion resistance. The high-volume fraction of precipitates significantly enhanced the strength of the alloy.

Research Status and Prospective Properties of the Al-Zn-Mg-Cu Series Aluminum Alloys

Investigation of Microstructures and Mechanical Properties of Ultra-High Strength Al-Zn-Mg-Cu Alloy Prepared by Rapid Solidification and Hot Extrusion

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Improved Strength and Enhanced Pitting Corrosion Resistance of Al-Mn Alloy with Zr Addition

Thermodynamic, Kinetic and Strength Calculation of High Zinc Containing Al-Zn-Mg-Cu Alloys

Precipitation hardening and intergranular corrosion behavior of novel Al–Mg–Zn(-Cu) alloys

Al-Mg-Zn(-Cu) Cross-Over Alloys: The New Frontier in High-Strength and Radiation-Resistant Lightweight Materials

The Advancement of 7XXX Series Aluminum Alloys for Aircraft Structures: A Review

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Research Progress on Cu–15Ni–8Sn Alloys: The Effect of Microalloying and Heat Treatment on Microstructure and Properties

Synchronously enhancing the strength, toughness, and stress corrosion resistance of high-end aluminum alloys via interpretable machine learning

Research Progress on Multi-Component Alloying and Heat Treatment of High Strength and Toughness Al–Si–Cu–Mg Cast Aluminum Alloys

Microstructure, tensile properties and fracture behaviour of an Al-Cu-Li-Mg-Zr alloy 8090

Microstructure, Mechanical Properties and Corrosion Behavior of Mg-Zn-Zr Alloys with Different Compositions

Recent Progress on Regulating Strategies for the Strengthening and Toughening of High-Strength Aluminum Alloys

Multi-alloying effect of Ti, Mn, Cr, Zr, Er on the cast Al-Zn-Mg-Cu alloys

Role of alloying and heat treatment on microstructure and mechanical properties of cast Al-Li alloys: A review

Study on the effect of enhanced magnesium and copper contents on microstructure and property of Al-Zn-Mg-Cu alloys with high zinc element content during fabrication processes

Influence of Zr content on microstructure and mechanical properties of As-cast Al-Zn-Mg-Cu alloy

Effect of intermetallics on properties of Al-6.1Zn-2.3Mg-1.7Cu-0.15Zr-0.3Nd alloy: First-principles calculation