Abstract:Silicon carbide (SiC) is an effective material for high-temperature engineering applications owing to its desirable properties such as high elastic modulus, high hardness, and melting temperature, high thermal conductivity, good corrosion and oxidation resistance, low density, and coefficient of thermal expansion compared with other advanced ceramics. Nevertheless, poor sinterability and low toughness limit its use, which can be overcome using appropriate additives. In this study, the effect of different amounts of nano-β-SiC (0, 5, 10, and 15 wt.%) and graphene (0, 1, 2, and 3 wt.%) particles on the sinterability behavior and microstructure of SiC composite has been investigated. After weighing, dispersing nano-β-SiC and graphene, and mixing the starting materials, milling was carried out at 180 rpm for 3 h. The materials obtained were then compressed uniaxially under a pressure of 75 MPa and then were compressed again through CIP under 150 MPa. To remove volatile products, the pyrolysis process was performed at 800 °C under Ar atmosphere. Finally, the samples were sintered at 2200 °C for 2 h by the pressureless sintering process. XRD analysis was used to investigate the phases and FESEM images were used to study the microstructure. According to the XRD patterns, β-SiC particles were converted to α-SiC, which was accompanied by the elongation of SiC grains. Also, no reaction was observed between graphene and the SiC matrix. According to the FESEM images, the samples containing 5 wt.% nano-β-SiC and 1 wt.% graphene showed a uniform distribution of reinforcement particles but with increasing the amount of the reinforcement particles, agglomeration was observed. According to the results, upon increasing the nano-β-SiC up to 5 wt% and graphene up to 1 wt.%, all the measured properties including relative density, and linear shrinkage improved and reached 99.04%, and 18.01%, respectively. However, with increasing the additives, these properties deteriorated due to increasing porosity and agglomeration in the composite structure.

Mechanism of Retaining Graphite Phase in the Graphite/sic Composite by Condense Layer with Fine SiC Grain Reaction Formed Via Nano Carbon Black

Tribological properties of reaction-formed graphite/SiC composites under water-lubricated conditions

A novel porous carbon synthesized to serve in the preparation of highly dense and high-strength SiC/SiC by reactive melt infiltration

Enhanced strength and toughness of SiC/C composite ceramics via SiC@graphene core–shell nanoparticles

The microstructural evolution of isotropic graphite under silicon vapor infiltration

Investigations of the effect of Si addition on graphite elimination and the oxidation behavior of SiC joint using Inconel 625 powder filler

Fabrication of C/SiC composites by siliconizing carbon fiber reinforced nanoporous carbon matrix preforms and their properties

EFFECT OF AL(2)O(3) AND SIC CONTENT IN PACK CEMENTATION POWDERS ON THE MICROSTRUCTURE OF SIC COATINGS ON HTR GRAPHITE SPHERES

Microstructure and Mechanical Properties of Cf/SiC Composites with Dispersed C-SiC Interphase Prepared by Chemical Vapor Infiltration

Preparation of β-Sialon /SiC composite powder by carbothermal reaction of coal-mine schist

In-situ Preparation of Nano MoSi 2 SiC Composite by Melt Infiltration of Silicon Method

Effects of in situ formed nanostructures on the structure and properties of C/SiOC composites

Preparation and Properties of C/SiC Composites Reinforced by High Thermal Conductivity Graphite Films

Densification and Enhancement of Sic Particulate Reinforced Fine Grain Sic Ceramic

Preparation of Silicon Carbide/Graphite Composite Ceramic Sealing Material by Liquid Silicon Inifltration Processing

Preparation of Silicon Carbide Powder from Amorphous Silica and Investigation of Synthesis Mechanism

Pressureless sintering of SiC matrix composites reinforced with nano-β-SiC and graphene

Reactive infiltration processing of SiC/Fe-Si composites using preforms made of coked rice husks and SiC powder

Effect of impregnated phenolic resin on the properties of Si–SiC ceramic matrix composites fabricated by SLS-RMI

Coating dense Silicon Carbide layer on artificial graphites to achieve synergistically enhanced thermal conductivity and electronic insulation of polymer composites

Polycarbosilane as a modulator for reaction-bonded silicon carbide processing of GNPs/Si mixtures