Abstract:In present study, a novel Nb-V microalloyed Fe–Mn–Al–C steel and a non-microalloyed Fe–Mn–Al–C austenitic steel were treated with different thermo-mechanical processes. The microstructure of the test steels was observed by scanning electron microscope, transmission electron microscope, electron probe micro-analyzer, and X-ray diffractometer. A tensile test was conducted to estimate the mechanical properties of the test steels. Results show that the equiaxed austenitic grains are obtained in both test steels, while hot rolling reduces the grain size significantly. The grain size of the Fe–Mn–Al–C steel decreases by 40%–55% after the addition of Nb-V due to the precipitation of nanoscale (Nb,V)C particles within the austenite matrix. Compared with the solid solution treated specimens, the strength of the hot-rolled or aged specimens is improved. Meanwhile, the strength of the Fe–Mn–Al–C steel with Nb-V microalloying is also increased by 55 MPa due to the precipitation strengthening and fine grain strengthening, while the elongation is decreased. The Nb-V microalloyed Fe–Mn–Al–C steel, after hot rolling + aging treatment, obtains the maximum strength, with the yield and tensile strength of 669 MPa and 1001 MPa, respectively. The strengthening mechanisms that contribute significantly to the yield strength are solid solution strengthening and dislocation strengthening. They are 185 MPa and 211 MPa, respectively, for the Nb-V microalloyed Fe–Mn–Al–C steel at hot rolling + aging conditions. Meanwhile, the segregation of carbon atoms after aging treatment also improves the yield strength significantly. Further, it is revealed that the deformation mechanisms are microband-induced plasticity and dynamic slip band refinement.

The Effect of Nb/Mo on the Microstructures and Mechanical Properties of Fe-Mn-Al-Ni-C Austenitic Steels

Effect of Mo Content on Microstructure and Properties of 00cr12ni9mo (x) Cu2Ti Maraging Stainless Steel

The effect of Ti–Mo–Nb on the microstructures and tensile properties of a Fe–Mn–Al–C austenitic steel

Effect of Nb contents on microstructure characteristics and yielding behavior of Fe–4Mn–2Al-0.2C steel

Influence of Thermo-Mechanical Process and Nb-V Microalloying on Microstructure and Mechanical Properties of Fe–Mn–Al–C Austenitic Steel

Synergetic effects of complex additions of Mo and Ni on the phase transformation behavior and mechanical properties of austenitic lightweight steels

Microstructure and mechanical properties of a novel medium Mn steel with Cr and Mo microalloying

Effect of Mo on Nano‐Precipitation Behavior and Microscopic Mechanical Characteristics of Ferrite

Synergistic Effect of Al and Ni on Microstructure Evolutions and Mechanical Properties of Fe-Mn-Al-C Low-Density Steels

Effect of Cr–Mo addition on the microstructure and mechanical properties of medium‐carbon steel

Effect of Mo and Nb on mechanical properties and hydrogen embrittlement of hot-rolled medium-Mn steels

EFFECT OF MOLYBDENUM ON DELAYED FRACTURE BEHAVIOR OF HIGH STRENGTH STEEL

Unexpected strengthening of the Mo-containing low-density steel achieved through a novel nano-ordered phase

Effect of Molybdenum on the Impact Toughness of Heat-Affected Zone in High-Strength Low-Alloy Steel

Impact of Mo/Ni Alloying on Microstructural Modulation and Low-Temperature Toughness of High-Strength Low-Alloy Steel

Effect of Mo Alloying on the Precipitation Behavior of B2 Nano-Particles in Fe-Mn-Al-Ni Shape Memory Alloys

Effect of Nb content on the stacking fault energy, microstructure and mechanical properties of Fe-25Mn-9Al-8Ni-1C alloy

Effect of W/Mo ratio on the as-cast microstructure of Nb-modified Hastelloy N alloys

Effect of Mo addition on the microstructure and high-specific tensile strength of Fe–Mn–Al–Ni–C ferrous medium-entropy alloy

Refinement mechanism of nanoscale Cu-rich precipitates by Mo addition and its effect on strength-toughness of Cu-bearing low carbon high strength steel

Effects of Mo Addition on Microstructure of a 4th Generation Ni-based Single Crystal Superalloy