Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Polythiophene Solar Cells Processed from Non-Halogenated Solvent with 15.68% Efficiency

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Polythiophenes for organic solar cells with efficiency surpassing 17%

Improving Efficiency of Non-Fullerene Polymer Solar Cells by Using Non-Halogenated Solvents

Enhanced Performance of P3HT-based Non-Fullerene Polymer Solar Cells by Optimizing Film Morphology Using Non-Halogenated Solvent

Solid Additive Tuning Polymer Blend Morphology Enables Non-halogenated-solvent All-polymer Solar Cells with Efficiency over 17%

Surpassing 13% Efficiency for Polythiophene Organic Solar Cells Processed from Nonhalogenated Solvent

Highly Efficient All‐Polymer Solar Cells Processed from Nonhalogenated Solvents

Non-halogenated solvent-processed single-junction polymer solar cells with 9.91% efficiency and improved photostability

Nonhalogenated‐Solvent‐Processed High‐Performance All‐Polymer Solar Cell with Efficiency over 14%

Molecular Design and Morphology Control Towards Efficient Polymer Solar Cells Processed Using Non‐aromatic and Non‐chlorinated Solvents

Tetrahydrofuran Processable Organic Solar Cells with 19.45% Efficiency Realized by Introducing High Molecular Dipole Unit Into the Terpolymer

All-Polymer Solar Cells Employing Non-Halogenated Solvent and Additive

Highly Efficient Perovskite Solar Cells Fabricated by Simplified One-Step Deposition Method with Non-Halogenated Anti-Solvents

Brominated Polythiophene Reduces the Efficiency‐Stability‐Cost Gap of Organic and Quantum Dot Hybrid Solar Cells

Non-halogenated Solvents for Environmentally Friendly Processing of High-Performance Bulk-Heterojunction Polymer Solar Cells

P3HT‐Based Polymer Solar Cells with 8.25% Efficiency Enabled by a Matched Molecular Acceptor and Smart Green‐Solvent Processing Technology

Delicately Controlled Polymer Orientation for High-Performance Non-Fullerene Solar Cells with Halogen-Free Solvent Processing.

Highly Efficient Solar Cells Based on the Copolymer of Benzodithiophene and Thienopyrroledione with Solvent Annealing

Critical Role of Non-Halogenated Solvent Additives in Eco-Friendly and Efficient All-Polymer Solar Cells

Binary Nonchlorinated and Nonaromatic Solvent-Processed PTB7:PC71BM and PTB7-Th:PC71BM Active Layers Showing Efficiency Comparable to That of Chlorobenzene in Organic Solar Cells