Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Molecular Design and Morphology Control Towards Efficient Polymer Solar Cells Processed Using Non‐aromatic and Non‐chlorinated Solvents

Methyl Functionalization on Conjugated Side Chains for Polymer Solar Cells Processed from Non-Chlorinated Solvents

Molecular Design Toward Efficient Polymer Solar Cells with High Polymer Content.

Delicately Controlled Polymer Orientation for High-Performance Non-Fullerene Solar Cells with Halogen-Free Solvent Processing.

Design, Application, and Morphology Study of a New Photovoltaic Polymer with Strong Aggregation in Solution State

Solid Additive Tuning Polymer Blend Morphology Enables Non-halogenated-solvent All-polymer Solar Cells with Efficiency over 17%

Non-halogenated solvent processable wide bandgap polymer based on carboxylate-substituted benzodithiophene for high-efficiency polymer solar cells

Improving Efficiency of Non-Fullerene Polymer Solar Cells by Using Non-Halogenated Solvents

Synchronously regulating the alkyl side-chain and regioisomer of polymerized small molecule acceptor enabling highly efficient all-polymer solar cells processed with non-halogenated solvent

Enhanced Performance of P3HT-based Non-Fullerene Polymer Solar Cells by Optimizing Film Morphology Using Non-Halogenated Solvent

Conjugated Polymers Based on Difluorobenzoxadiazole Toward Practical Application of Polymer Solar Cells

Highly Efficient Solar Cells Based on the Copolymer of Benzodithiophene and Thienopyrroledione with Solvent Annealing

Tethered Trimeric Small‐molecular Acceptors through Aromatic‐core engineering for Highly Efficient and Thermally Stable Polymer Solar Cells

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Rational design of conjugated side chains for high-performance all-polymer solar cells

Non-halogenated Solvents for Environmentally Friendly Processing of High-Performance Bulk-Heterojunction Polymer Solar Cells

Isomerized Green Solid Additive Engineering for Thermally‐Stable and Eco‐Friendly All‐Polymer Solar Cells with Approaching 19% Efficiency

Design of a thiophene-fused benzotriazole unit as an electron acceptor to build D–A copolymers for polymer solar cells

Nonhalogenated‐Solvent‐Processed High‐Performance All‐Polymer Solar Cell with Efficiency over 14%

High efficient polymer solar cell processed by environment-friendly solvent system