Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Polythiophenes for organic solar cells with efficiency surpassing 17%

Ternary Polythiophene Enables over 17% Efficiency Organic Solar Cells

Sequentially Fluorinated Polythiophene Donors for High‐Performance Organic Solar Cells with 16.4% Efficiency

Surpassing 13% Efficiency for Polythiophene Organic Solar Cells Processed from Nonhalogenated Solvent

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

19.36% Efficiency Organic Solar Cells Based on Low‐Cost Terpolymer Donors with Simple Molecular Structures

Tetrahydrofuran Processable Organic Solar Cells with 19.45% Efficiency Realized by Introducing High Molecular Dipole Unit Into the Terpolymer

Non-Halogenated Polymer Donor-Based Organic Solar Cells with a Nearly 15% Efficiency Enabled by a Classic Ternary Strategy

A Facile Synthetic Approach Based on Thieno[3,4-c]pyrrole-4,6-dione to Construct Polymer Donors for Highly-Efficient Organic Solar Cells

Direct Arylation Polycondensation‐Derived Polythiophene Achieves over 16% Efficiency in Binary Organic Solar Cells Via Tuning Aggregation and Miscibility

Tuning the Intermolecular Electrostatic Interaction toward High‐Efficiency and Low‐Cost Organic Solar Cells

The Renaissance of Oligothiophene‐Based Donor–Acceptor Polymers in Organic Solar Cells

Polythiophene Solar Cells Processed from Non-Halogenated Solvent with 15.68% Efficiency

A Nonfullerene Acceptor Utilizing a Novel Asymmetric Multifused-Ring Core Unit for Highly Efficient Organic Solar Cells

Preparing polythiophene derivative with alternating alkyl and thioalkyl side chains <i>via</i> Kumada coupling for efficient organic solar cells

Ordering structure control of polythiophene-based donors for High-Efficiency organic solar cells

A Thiazole-Based Polymer Donor for Efficient Organic Solar Cells

Highly Efficient Ternary-Blend Polymer Solar Cells Enabled by a Nonfullerene Acceptor and Two Polymer Donors with a Broad Composition Tolerance.

A Thiadiazole‐Based Conjugated Polymer with Ultradeep HOMO Level and Strong Electroluminescence Enables 18.6% Efficiency in Organic Solar Cell

Volatilizable Solid Additive‐Assisted Treatment Enables Organic Solar Cells with Efficiency over 18.8% and Fill Factor Exceeding 80%

Green solvent-processed organic solar cells based on a low cost polymer donor and a small molecule acceptor