Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Tetrahydrofuran Processable Organic Solar Cells with 19.45% Efficiency Realized by Introducing High Molecular Dipole Unit Into the Terpolymer

Efficient Organic Solar Cells Processed from a Halogen-Free Solvent Based on Benzo[1,2-B:4,5-B]difuran Terpolymers

Surpassing 13% Efficiency for Polythiophene Organic Solar Cells Processed from Nonhalogenated Solvent

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

High‐Performance Green Thick‐Film Ternary Organic Solar Cells Enabled by Crystallinity Regulation

Bihalogenated Thiophene-Based Terpolymers for High-Performance Semitransparent Organic Solar Cells Processed by an Eco-Friendly Solvent and Layer-by-Layer Deposition

Polythiophenes for organic solar cells with efficiency surpassing 17%

Sequentially Fluorinated Polythiophene Donors for High‐Performance Organic Solar Cells with 16.4% Efficiency

High-efficiency Organic Solar Cells Processed from a Halogen-Free Solvent System

Halogenation Strategy of Thiophene Derived Solvent Additives Enables Optimized Morphology for Organic Solar Cells with 19.17% Efficiency

Achieving 12.6% Efficiency in Single‐Component Organic Solar Cells Processed from Nonhalogenated Solvents

Hydrogen Bond Induced Green Solvent Processed High Performance Ternary Organic Solar Cells with Good Tolerance on Film Thickness and Blend Ratios

Non-Halogenated Solvents Processed Efficient ITO-Free Flexible Organic Solar Cells with Upscaled Area

Air‐Processed Efficient Organic Solar Cells from Aromatic Hydrocarbon Solvent without Solvent Additive or Post‐Treatment: Insights into Solvent Effect on Morphology

Binary Organic Solar Cells with Exceeding 19% Efficiency via the Synergy of Polyfluoride Polymer and Fluorous Solvent

To Fluorinate or Not to Fluorinate in Organic Solar Cells: Achieving a Higher PCE of 15.2% when the Donor Polymer is Halogen‐Free

Oligomeric Semiconductors Enable High Efficiency Open Air Processed Organic Solar Cells by Modulating Pre-aggregation and Crystallization Kinetics

Green‐Solvent‐Processed Organic Solar Cells with Approaching 20% Efficiency and Improved Photostability

19.36% Efficiency Organic Solar Cells Based on Low‐Cost Terpolymer Donors with Simple Molecular Structures

Volatilizable Solid Additive‐Assisted Treatment Enables Organic Solar Cells with Efficiency over 18.8% and Fill Factor Exceeding 80%

Fully Non‐Fused Ring Electron Acceptors Enable Effective Additive‐Free Organic Solar Cells with Enhanced Exciton Diffusion Length