Abstract:This paper presents characterization and compensation of the thermal bias drift of a MEMS accelerometer whose effective stiffness is electrostatically tuned to a low value with the help of the single-sided parallel plates (SSPPs) capacitors. A temperature drift model for the proposed accelerometer is built and the temperature effect on the mechanical stiffness and the circuit gains is characterized. The characterization reveals that the variations of the feedforward coefficient including the mechanical stiffness and the readout gain due to the temperature change play a significant role in the bias drift of output of the proposed closed-loop accelerometer. On the other hand, the variations of both feedback gain and tuning gain as a function of temperature are one-order-of-magnitude less than that of the feedforward coefficient. To calibrate the feedforward coefficient, an excitation signal as a form of AC reference displacement is introduced to drive the proof mass and the readout response is demodulated to calibrate the variance of the feedforward coefficient correspondingly. An open-loop compensation scheme for the temperature-induced bias drift using the variance of the calibrated response is proposed accordingly. Alternatively, the calibrated response can be controlled to a preset value by a new proportion integral derivative (PID) controller by the adjustment of the SSPP tuning voltage. The output of the PID controller is used for the calibration of the introduced bias from the electrostatic tuning force. Therefore, a closed-loop compensation of the thermal bias drift is achieved by remaining the feedforward coefficient while eliminating the calibrated bias. Experiments under a temperature cooling process and different tuning voltages are carried out to verify two proposed compensation schemes. The temperature drift coefficients (TDCs) of both compensated outputs exhibit at least one-order-of-magnitude reduction in response to the temperature change. When the effective stiffness of the accelerometer is tuned to about 4.19 N m(-1), the TDC of the compensated output using the proposed open-loop or closed-loop compensation schemes is reduced to about 0.1136 or 0.0391 mg degrees C-1, respectively and meanwhile, the Allan bias instability is slightly increased to 48.63 or 56.14 mu g, respectively.

Thermal Stabilization of Quality Factor for Dual-Axis MEMS Gyroscope Based on Joule Effect in Situ Dynamic Tuning

120 Ppm Quality Factor Thermal Stability from -40 ℃ to +60℃ of a Dual-Axis MEMS Gyroscope Based on Joule Effect Dynamic Control

A Sub-0.1°/H Bias-Instability MEMS Gyroscope Using Resonant Constant-Frequency Driving Technique

MEMS gyroscopes parametric excitation control scheme with constant resonant frequency

A 0.09°/h Bias-Instability MEMS Gyroscope Working with a Fixed Resonance Frequency

One-time Frequency Sweep to Eliminate IQ Coupling in MEMS Vibratory Gyroscopes

Bias Thermal Stability Improvement of MEMS Gyroscope with Quadrature Motion Correction and Temperature Self‐sensing Compensation

Drive Mode Control for MEMS Gyroscopes with Electrostatically Tunable Structure

Identification and Suppression of Driving Force Misalignment Angle for a MEMS Gyroscope Using Parametric Excitation

A Real-Time Temperature Compensation Algorithm for a Force-Rebalanced MEMS Capacitive Accelerometer Based on Resonant Frequency.

Temperature-dependence improvement for a MEMS gyroscope using triangular-electrode based capacitive detection method

Characterization and Compensation of Thermal Bias Drift of a Stiffness-Tunable MEMS Accelerometer

Performance Improvement for MEMS Gyroscopes by Suppressing the Circuit Phase Delay

Low-Noise Quality Factor Tuning in Nondegenerate MEMS Gyroscope Without Dedicated Tuning Electrode

A Research on Temperature Dependent Characteristics of Quality Factor of Silicon MEMS Gyroscope

A Temperature Characteristic Research and Compensation Design for Micro-Machined Gyroscope

A Temperature Control System Used for Improving Resonant Frequency Drift of MEMS Gyroscopes.

Driving-force compensation to improve the bias thermal stability of MEMS gyroscopes

A High-Performance Tactical-Grade Monolithic Horizontal Dual-Axis MEMS Gyroscope with Off-Plane Coupling Suppression Silicon Gratings

A Temperature Drift Suppression Method of Mode-Matched MEMS Gyroscope Based on a Combination of Mode Reversal and Multiple Regression

An 8PPM/°C Temperature Sensitivity of the Scale Factor in MEMS Gyroscope Based on Multi Parameters Fusion Compensation Method