Abstract:Multi-layer crystallization and uncontrollable defects were the main factors that limiting the quality of Cu 2 ZnSn(S,Se) 4 (CZTSSe) films. Here a hybrid crystallization strategy was proposed to simultaneously improve the morphology and defect properties of CZTSSe film. Firstly, we found the variation of the microstructures (constitution, chemical environment of the elements, etc.) in precursor films can greatly alter the grain-growths of CZTSSe films. Detailed characterizations revealed that the chemical environment of S in the precursor film may influence the S-to-Se substitution of the film during the selenization process. This can further affect the grain-growth mechanism and the properties of CZTSSe film. While the S-to-Se substitution of the film mainly occurred below 500°C, the NaSe x on the surface of the film could dominate the grain-growth (Na-mechanism). For this mechanism, the CZTSSe film exhibited bi-layer morphology and relatively high band-tail energy, but shallow-acceptor was detected in the film. The solar cells based on the CZTSSe films reached the efficiency of 10.6%. As a comparison, liquid phase could be generated when the S-to-Se substitution of the film shifted to higher temperature (>500°C). In this condition, the grain-growth would be dominated by the liquid phase (LP-mechanism). Such mechanism can eliminate the multi-layer crystallization and reduce the band-tail energy, but the surface properties of the CZTSSe film was deteriorated and the formation of shallow-acceptor in CZTSSe was inhibited. The fabricated solar cells achieved the efficiency of 10.3%. Based on the results above, a bi-layer precursor film contained sub-layers with different microstructures was proposed to regulate the crystallization of CZTSSe. The co-existence of different microstructures in the precursor film could induce a hybrid grain-growth mechanism for the CZTSSe film (e.g., the Na-mechanism worked on the surface while the LP-mechanism worked in the bottom simultaneously). Such grain-growth mechanism can yield CZTSSe film with uniform morphology and favorable defect properties. The CZTSSe solar cells based on the hybrid grain-growth mechanism achieved the best efficiency of 12.6%. The investigation in this paper would provide new solutions for the crystallization regulation on CZTSSe photovoltaic material.

Gradient Band Gap CZTSSe Prepared Via Sputtering from Quaternary Ceramic Targets Followed with Annealing under Different Atmospheres

CZTSSe solar cell with an efficiency of 10.19% based on absorbers with homogeneous composition and structure using a novel two-step annealing process

A Study on Cr Incorporation to Enhance Performance of CZTSSe Solar Cells Via Optimizing Selenization Condition

Controllable Double Gradient Bandgap Strategy Enables High Efficiency Solution‐Processed Kesterite Solar Cells

Further Boosting Solar Cell Performance Via Bandgap-Graded Ag Doping in Cu2ZnSn(S,Se)4 Solar Cells Compared to Uniform Ag Doping

Improving the Performance of Solution-Based CZTSSe Absorber by Selenization Annealing with Selenium Powder in Argon

On the Growth Process of Cu2ZnSn(S,Se)4 Absorber Layer Formed by Selenizing Cu–ZnS–SnS Precursors and Its Photovoltaic Performance

Effects of Selenization Conditions on Microstructure Evolution in Solution Processed Cu2ZnSn(S,Se)(4) Solar Cells

Cu2ZnSn(S, Se)4 solar cell with slight band tailing states achieves 11.83% efficiency by selenizing sputtered Cu–Zn–Sn–S precursor

The enhancement of CZTSSe solar cell performance through active construction of the double-layer absorber

Controlling selenization equilibrium enables high-quality Cu2ZnSn(S, Se)4 absorbers for efficient solar cells

Formation of the Front-Gradient Bandgap in the Ag Doped CZTSe Thin Films and Solar Cells

Microenvironment Created by SnSe2 Vapor and Pre‐Selenization to Stabilize the Surface and Back Contact in Kesterite Solar Cells

Passivation of Deep‐Level Defects through Chemical Environment Regulation for Efficient CZTSSe Solar Cells Based on Active Selenium Adsorption–Desorption Process

Eliminating Cracking Morphology of Solution-Processed CZTSSe Absorbers by Sn-rich Composition Engineering

Achieving 11.95% Efficient Cu2ZnSnSe4 Solar Cells Fabricated by Sputtering a Cu-Zn-Sn-Se Quaternary Compound Target with a Selenization Process

Growth of Large Grain-Size Cu2ZnSn(SxSe1-x)4 Thin Films by Annealing Precursors Sputtered from a Single Quaternary Target for Solar Cells Application

Using soda-lime glass transition temperature to enhance the efficiency of Cu2ZnSn(S,Se)4 solar cell

A Robust Approach to Fabricate CZTSSe Absorber Layer for Solar Cells Via a Self-Selenizations Process Conducted by Concentrated Selenium Solution

Highly Efficient Cu2ZnSn(S,Se)4 Bifacial Solar Cell Via a Composition Gradient Strategy Through the Molecular Ink

Simultaneously improving the morphology and defect properties of CZTSSe film via hybrid grain-growth mechanism