Abstract:A novel segmented control strategy for selenization environment is introduced to regulate the selenization reaction by controlling the evaporation area of Se. This selenization method helps to promote element homogenization, optimize surface smoothness, and obtain a high‐crystalline‐quality absorber with low‐point defects. And the CZTSSe solar cell with a PCE of 13.77% is successfully achieved. High‐crystalline‐quality absorbers with fewer defects are crucial for further improvement of open‐circuit voltage (VOC) and efficiency of Cu2ZnSn(S,Se)4 (CZTSSe) solar cells. However, the preparation of high‐quality CZTSSe absorbers remains challenging due to the uncontrollability of the selenization reaction and the complexity of the required selenization environment for film growth. Herein, a novel segmented control strategy for the selenization environment, specifically targeting the evaporation area of Se, to regulate the selenization reactions and improve the absorber quality is proposed. The large evaporation area of Se in the initial stage of the selenization provides a great evaporation and diffusion flux for Se, which facilitates rapid phase transition reactions and enables the attainment of a single‐layer thin film. The reduced evaporation area of Se in the later stage creates a soft‐selenization environment for grain growth, effectively suppressing the loss of Sn and promoting element homogenization. Consequently, the mitigation of Sn‐related deep‐level defects on the surface and in the bulk induced by element imbalance is simultaneously achieved. This leads to a significant improvement in nonradiative recombination suppression and carrier collection enhancement, thereby enhancing the VOC. As a result, the CZTSSe device delivers an impressive efficiency of 13.77% with a low VOC deficit.

Effects of Selenization Conditions on Microstructure Evolution in Solution Processed Cu2ZnSn(S,Se)(4) Solar Cells

Formation of Alloyed Cu2Cox Zn1-x Sn(S,Se)4 Absorption Layer and Its Application in Solar Cells

Segmented Control of Selenization Environment for High‐Quality Cu2ZnSn(S,Se)4 Films Toward Efficient Kesterite Solar Cells

Exploring the optimal two-step selenization process to enhance the performance of ionic liquid solution based Cu2ZnSn(S,Se)4 thin film solar cells

An investigation on phase transition for as-sputtered Cu 2 ZnSnSe 4 absorbers during selenization

Passivation of Deep‐Level Defects through Chemical Environment Regulation for Efficient CZTSSe Solar Cells Based on Active Selenium Adsorption–Desorption Process

Unveiling the Selenization Reaction Mechanisms in Ambient Air-Processed Highly Efficient Kesterite Solar Cells

Optimized grain growth for efficient solution-processed Bi-doped Cu2ZnSn(S,Se)4 thin film solar cells via spin-coated layers adjustment and two-step selenization

Controlling selenization equilibrium enables high-quality Cu2ZnSn(S, Se)4 absorbers for efficient solar cells

Improving the Performance of Solution-Based CZTSSe Absorber by Selenization Annealing with Selenium Powder in Argon

Microenvironment Created by SnSe2 Vapor and Pre‐Selenization to Stabilize the Surface and Back Contact in Kesterite Solar Cells

Achieving 11.95% Efficient Cu2ZnSnSe4 Solar Cells Fabricated by Sputtering a Cu-Zn-Sn-Se Quaternary Compound Target with a Selenization Process

Effects of Selenization on Phase Transition and S/(S+Se) Ratios of As-Deposited Cu2ZnSnS4 Absorbers Sputtered by a Quaternary Target

Grain growth of CZTSSe via nanocrystal selenization

Regulating Hetero‐Nucleation Enabling Over 14% Efficient Kesterite Solar Cells

Effects of Selenium Atmosphere on Grain Growth for CZTSe Absorbers Fabricated by Selenization of As-Sputtered Precursors

Using soda-lime glass transition temperature to enhance the efficiency of Cu2ZnSn(S,Se)4 solar cell

Significantly Improving the Crystal Growth of a Cu 2 ZnSn(S,Se) 4 Absorber Layer by Air-Annealing a Cu 2 ZnSnS 4 Precursor Thin Film

Preparing Cu2ZnSnSe4 thin film solar cells based on selenium containing precursors

Formation of Alloyed Cu2CoxZn1-xSn(S,Se)4 Absorption Layer and Its Application in Solar Cells.

Cu2ZnSnSSe4 Solar Cells with 9.6% Efficiency Via Selenizing Cu-Zn-Sn-S Precursor Sputtered from a Quaternary Target