Abstract:The influences of temperature, SO2, water vapor and simulated ash on the high-temperature corrosion of an Fe-Ni-based alloy HR6W at 750 degrees C and 810 degrees C for 1000 h was systematically investigated. The weight gains and characterization of the corrosion products formed on the HR6W alloy in various environments were used to obtain the high-temperature corrosion behaviors of the alloy. The results show that weight gains of alloy HR6W under various gas conditions at 750 degrees C and 810. C was much lower than that of the samples coated with salt, indicating that alloy HR6W exhibited excellent corrosion resistance due to a Cr2O3-rich scale. The SO2 promoted crackings of the Cr-rich oxide scales at 750 degrees C and 810 degrees C. After exposure to air containing water vapor and SO2, the corrosion products were mainly composed of an outer layer of Fe2O3, a small amount of NiO and an inner layer of Cr2O3. Sulfidation of alloy HR6W underneath the Cr-rich oxide scale was clearly observed on the samples exposed to SO2 and on all samples coated with salt. Additional NiO was found on the samples coated with salt exposed to air containing SO2. Alloy HR6W coated with salt exposed to air containing SO2 at 750 degrees C and 810 degrees C experienced the most severe corrosion among all samples herein due to the high causticity of the alkali-iron-trisulfates. The key elements affecting the high-temperature corrosion of alloy HR6W in the various gas environments were temperature > SO2>water vapor, in the order. Under the gas-molten salt conditions, the SO2 played the most important role in determining the corrosion rate. The key elements were SO2> temperature > water vapor, in that order.

Characterization and Simulation Studies on the Corrosion Products of HR230 and 740 H Alloys in CO2 with 7% H2O Environment at 1000 ℃

Revealing the Role of SO2 in the High-Temperature Corrosion Diffusion of Two Superalloys in CO2 Through Molecular Dynamics and Thermal Stability

Revealing the Effect of O2, SO2 and H2O in Supercritical CO2 on the Corrosion Behavior of 316L Steel at Elevated Temperature

Molecular Dynamics, Thermodynamics and Experimental Studies on the Corrosion Mechanism of T92 and TP347H Steels in High-Pressure CO2 and H2O at 600 °C

The Corrosion Behavior of Co-Cr-Al Alloys Exposed to Mixed Oxygen-Sulfur Atmospheres at 900 °C

Corrosion Behavior of Heat-Resistant Materials in High-Temperature Carbon Dioxide Environment

Corrosion Behaviour of Ni-based Alloys 230, 617, and 601 in CO2 Gas at 750 and 850°C

High-temperature Corrosion of an Fe–Ni-based Alloy HR6W under Various Conditions at 750 °C and 810 °C: Effect of the Temperature, Water Vapor, Simulated Ash and SO2

Characteristics of the Corrosion Products on Three Scratched Heat-Resisting Alloys in Closed-Loop Supercritical and High-Temperature CO2

Effect of Fe on the Oxidation, Sulfidation and Carburization Behaviors of Alloys in CO2 Containing SO2

High-Temperature Corrosion Behaviors of Ni-Based Alloys in Carbon Dioxide

Corrosion Behaviors of Mg-7Gd-5Y-1Nd-0.5Zr Alloys in CO<sub>2</sub> Atmosphere under Different Relative Humidity

Effect of Cyclic Reaction on Corrosion Behavior of Chromium-Containing Alloys in CO2 Gas at 650 °C

Corrosion of Alloy Haynes 230 in High Temperature Supercritical Carbon Dioxide with Oxygen Impurity Additions

Characterization of Oxide Scales on Super-Alloy HR120 at 1000 °C in Air and Steam Environments

Corrosion Behaviour of AISI 430 Stainless Steel in O2-40%H2O at 800 °C

Scaling Behavior of Four Co-20Ni-xCr-yAl (x = 8,15 Wt.%; Y = 3,5 Wt.%) Alloys Exposed to 1 Atm O2 at 1000 °C and 1100 °C

Effect of water vapor content on the corrosion mechanism of HR3C in simulated oxy-coal combustion environment

Comparative Study On Oxidation Behavior Of Fe-5wt% Cr Alloy In Various Mixed Atmospheres At 900-1000 Degrees C

Molecular Dynamics Study on the Initial Oxidation Behavior of FeCr Alloys in Supercritical H2O and Supercritical CO2 with O2

Corrosion Performance of Heat-Resisting Steels and Alloys in Supercritical Carbon Dioxide at 650 °C and 15 MPa