Abstract:Abstract The corrosion behavior of two stainless steels (310S and alumina-formed 310S) treated by different surface treatment methods (polishing or grinding) has been investigated after exposed to high-temperature supercritical carbon dioxide (sCO2) at 650°C / 20 MPa. The microstructure and microchemistry of materials have been analyzed and compared before and after exposure. The results show that polishing deteriorates the corrosion resistance, while grinding enhances the anti-oxidation and anti-carburization capability of materials. Thick and unprotective Fe-rich oxides are formed on the polished 310S and alumina-formed 310S, which leads to the poor carburization resistance. Much thinner oxides and shallower carburization depths can be observed on the materials treated by grinding. Continuous Cr-rich oxide is formed on the grinded 310S, while outer Cr-rich and inner Al-rich oxides are formed on the grinded alumina-formed 310S. Grinding deforms the surface region of materials. An outer ultra-fine grain layer and an inner highly deformed grain layer are located at the surface, which own fast diffusion paths and enhance the element diffusion rates (especially Cr and Al). This leads to the transition from the formation of unprotective Fe-rich oxide layers to the protective Cr-rich or Al-rich oxide layers, which not only hinders further oxidation of the matrix, but also reduces the carbon permeation. Improved oxidation and carburization resistance therefore occurs on the materials treated by grinding after exposed to high temperature sCO2 environment.

Characteristics of the Corrosion Products on Three Scratched Heat-Resisting Alloys in Closed-Loop Supercritical and High-Temperature CO2

Revealing the Effect of O2, SO2 and H2O in Supercritical CO2 on the Corrosion Behavior of 316L Steel at Elevated Temperature

Study on Corrosion Characteristics of Heat-resistant Materials in Supercritical Carbon Dioxide Environment Containing Oxygen Impurities

High-Temperature Corrosion Behavior of T92, TP347HFG and IN625 with Surface Scratching in Carbon Dioxide at 600 °C

Corrosion Performance of Heat-Resisting Steels and Alloys in Supercritical Carbon Dioxide at 650 °C and 15 MPa

Corrosion Behavior of Heat-Resistant Materials in High-Temperature Carbon Dioxide Environment

Molecular Dynamics, Thermodynamics and Experimental Studies on the Corrosion Mechanism of T92 and TP347H Steels in High-Pressure CO2 and H2O at 600 °C

CORROSION BEHAVIOR OF SUPER-AUSTENITIC STAINLESS STEEL AL-6XN IN SUPERCRITICAL WATER

Corrosion and Carburization Behavior of Heat-Resistant Steels in a High-Temperature Supercritical Carbon Dioxide Environment

Corrosion behavior of a new alumina-forming duplex stainless steel with different surface treatment in supercritical carbon dioxide

Effects of Corrosion in Supercritical CO2 on the Microstructural Evolution in 800H Alloy

Effect of Surface Treatment on the Corrosion Behavior of Stainless Steels in High-Temperature Supercritical Carbon Dioxide

Corrosion Behavior of Titanium Alloy Ti6Al4V in Supercritical Carbon Dioxide at 600°C

Characterization and Simulation Studies on the Corrosion Products of HR230 and 740 H Alloys in CO2 with 7% H2O Environment at 1000 ℃

Compatibility of Different Commercial Alloys in High-Temperature, Supercritical Carbon Dioxide

The surface grinding-induced oxide scale exfoliation of an austenitic alloy in supercritical CO<sub>2</sub>

Comparison of the corrosion of materials in supercritical carbon dioxide, air, and argon environments

The Effect of Surface Grinding on the Stress Corrosion Cracking Initiation of 316LN Stainless Steel in 600oc Supercritical CO2

Corrosion Behaviors of Heat-Resisting Alloys in High Temperature Carbon Dioxide

Corrosion Behavior and Lifetime Prediction of VM12, Sanicro 25 and Inconel 617 in Supercritical Carbon Dioxide at 600 °C

Corrosion of Alloy Steels Containing 2% Chromium in CO2 Environments