Abstract:This study uses ablation testing on C/SiC composite materials under local structured thermal sources with a wide range of heat flux densities, simulating the harsh local conditions caused by discontinuous structural interference on spacecrafts. The thermal response, ablation laws, and ablative perforation time of C/SiC composite materials are obtained under different heat flux densities. The experimental findings demonstrate that there are notable differences in the morphology of the ablation pits under various heat flux conditions. As the heat flux density increases, the temperature of the local structure heat source action center on the target surface increases, the depth and outer diameter of the erosion pits increase, and the wall surface of the erosion pits gradually tends to be smooth. Under the influence of local structural heat sources, the creation of material ablation pits and the process of material perforation are predicted using the improved Umeshmotion+ALE+birth and death element method. For various conditions, the temperature field results and ablation morphology are well predicted by the numerical simulation results. Numerical calculations can be used to analyze the thermal stress and oxidation sublimation contribution rates of targets under the action of structural heat sources.

Comparative Study of Microstructure and Ablation Behaviour of C/C-Hfc-Sic Composites Prepared under Two Different Conditions

Microstructure and ablation resistance of C/C-HfC-SiC composites prepared by RMI with different powder particle sizes

Microstructure and ablation behavior of C/C–HfC–SiC composites fabricated by reactive melt infiltration with Hf–Si alloy

Microstructure and Ablation Behavior of C/C-SiC-(ZrxHf1−x)C Composites Prepared by Reactive Melt Infiltration Method

Microstructure and Ablation Performance of SiC–ZrC Coated C/C Composites Prepared by Reactive Melt Infiltration

Comparative ablation behaviors of C/SiC–ZrC and C/SiC–HfC composites prepared by ceramization of carbon aerogel preforms

C/C-HfC-SiC composites with simultaneous the resistance to ultra-high temperature airflow erosion and high temperature oxidation

Ablation mechanism and morphology evolution of the HfC-SiC coating for C/C composites deposited by supersonic atmospheric plasma spraying

Comparison of the ablation resistance of mullite modified C/C-SiC-HfC and C/C-SiC-HfC composites under oxyacetylene flame of 2.38 MW/m 2 heat flux

Construction of sandwich-structured C/C-SiC and C/C-SiC-ZrC composites with good mechanical and anti-ablation properties

SiC Nanowires Toughed HfC Ablative Coating for C/C Composites

Preparation and Properties of C/SiC Composites Reinforced by High Thermal Conductivity Graphite Films

Study on the ablation performance of SiC-coated high thermal conductivity three-dimensional C/C composites

Study on the Ablation Behavior of C/SiC Composite Materials under the Action of Local Structural Thermal Sources

Cyclic ablation behavior of mullite-modified C/C-HfC-SiC composites under an oxyacetylene flame at about 2400 °C

Ablation behavior of Cf/ZrC-SiC and Cf/SiC composites produced by precursor infiltration and pyrolysis combined with gaseous silicon infiltration

Microstructure and ablation behaviour of C/C-SiC-ZrC-Cu composites prepared by reactive melt infiltration

Microstructure and flexural strength of C/HfC-ZrC-SiC composites prepared by reactive melt infiltration method

Effect of Si, Al2O3 additives on the ablation behavior of ZrB2-SiC coating with Al2O3-modified SiC bond coat for C/C composites

Effect of mullite content on microstructure and ablation behavior of mullite modified C/C-SiC-HfC composites

Microstructure and Ablation Behavior of W/ZrC/SiC Coating on C/C Composites Prepared by Reactive Melt Infiltration and Atmospheric Plasma Spraying