Abstract:The aim of the work was to create a selective gas sensor for hydrogen sulphide. As a result of adding ammonia to the zinc acetate solution, centrifuging the obtained zinc hydroxide and subsequent calcination, a polydisperse zinc oxide powder with a grain size of 5–50 nm was obtained. The material was characterized using X-ray phase analysis and transmission electron microscopy. Subsequently, silver nitrate and terpeniol were added to the zinc oxide nanopowder to form a paste. The gas-sensitive material was obtained by applying the resulting paste on a special dielectric substrate and subsequent calcination, as a result of which the terpeniol burned out, and the silver nitrate turned into an oxide (the mass fraction of the silver was 3%). A non-stationary temperature mode for the operation of the sensor was selected, in which, after rapidheating of the sensor to 450 °C (2 seconds), slow (13 seconds) cooling to 100 °C occurred. Each subsequent heating-cooling cycle with a total period of 15 seconds began immediately after the end of the previous cycle. The use of an unsteady temperature mode in combination with the selection of the composition of the gas-sensitive layer made it possible to obtain a response of 200 for a hydrogen sulphide concentration of 1 ppm. Along with an increase in sensitivity, a significant increase in selectivity was also observed. The cross-sensitivity for the determination of hydrogen sulphide and other reducing gases (CO, NH3, H2) was more than three orders of magnitude. Thus, this sensor can be used to detect hydrogen sulphide even in the presence of interfering components. The use of highly selective sensors in the tasks of qualitative andquantitative analysis can significantly simplify the calibration in comparison with “electronic nose” devices. Devices based on highly selective sensors do not require the use of mathematical methods for processing multidimensional data arrays.

Determination of Hydrogen Sulphide in Air with an Indium Oxide Semiconductor Sensor

Semiconductor metal oxide sensor for hydrogen sulphide operating under non-stationary temperature conditions

Polyaniline/CuO Nanoparticle Composites for Use in Selective H 2 S Sensors

Colloidal Synthesis of Tungsten Oxide Quantum Dots for Sensitive and Selective H2S Gas Detection

Identification of H2S Impurity in Hydrogen Using Temperature Modulated Metal Oxide Resistive Sensors with a Novel Signal Processing Technique

In2O3 Decorated Co32 Cluster for High Performance H2S MEMS Sensors

Exploiting Free-Standing p-CuO/n-TiO 2 Nanochannels as a Flexible Gas Sensor with High Sensitivity for H 2 S at Room Temperature

Study of a New Hydrogen Sensor Based on the Synthesis of a Sputtered In–Sn–Zn-O Thin Film and Evaporated Palladium Nanoparticles

Trace Hydrogen Sulfide Sensing Inspired by Polyoxometalate-Mediated Aerobic Oxidation

ZnO@CuO hollow nanospheres based composites used for sensitive detection of hydrogen sulfide with long-term stability

Chemisorption of hydrogen on metal oxides with palladium (II) oxide additives

High-Performance H2S Sensors to Detect SF6 Leakage

Screen-Printed Sensors for Colorimetric Detection of Hydrogen Sulfide in Ambient Air

Highly Sensitive and Selective NiO/WO 3 Composite Nanoparticles in Detecting H 2 S Biomarker of Halitosis

Pd/Pt-Bimetallic-Nanoparticle-Doped In2O3 Hollow Microspheres for Rapid and Sensitive H2S Sensing at Low Temperature

Pure-Water-Soluble Colorimetric Chemosensors for Highly Sensitive and Rapid Detection of Hydrogen Sulfide: Applications to Evaluation of On-Site Water Quality and Real-Time Gas Sensors

Development of an assay for colorimetric and fluorometric detection of H2S

A Sensing Properties Study On Miniature Au/SnO2 Gas Sensor For Hydrogen Sulfide Detection

Hydrogen detecting characteristics of a palladium nanoparticle/indium gallium oxide based sensor

Nanomaterials for the Selective Detection of Hydrogen Sulfide in Air

The detection of H2S at room temperature by using individual indium oxide nanowire transistors