Abstract:For single phase to ground fault in distribution networks, fault locating using traveling wave measured at one terminal only need to detect the arrival time of the initial wave head of the line mode and the zero mode. But the zero mode wave velocity is unstable. This paper proposes a fault section location method using only line mode traveling wave. It analyzes wave refraction and reflection performance at the fault point, the branch point and the end of the line. The path differences between reflected waves and the initial incident wave are estimated through Hilbert Huang Transform by indexing the arrival time of the initial wave and reflected waves, if the line mode wave velocity is assumed. Combined with the topology of distribution network, the possible propagation paths can be obtained to identify the fault section. The effectiveness of the proposed method is verified by experiments in the actual distribution network. Introduction In the distribution networks, the probability of occurrence of single phase to ground fault accounts for more than 80% of all types of faults. When single phase grounding occurs, it is of great significance to find fault location timely to improve power supply reliability. Fault location method based on transient traveling wave signal has been widely concerned because it is not affected by fault types, transition resistance and neutral grounding mode[1-2]. Modern traveling wave positioning methods are generally divided into single-ended method and double-ended method. The double-ended method uses the difference of arrival time of line mode traveling wave head between the two end measurement points to achieve fault location, requiring accurate global positioning system (GPS) on the time device [3]. Since the reflected wave from the fault point is difficult to identify, the single-ended method based on the initial traveling wave and the fault point reflected wave is difficult to apply in the actual distribution network [4,5]. Another single-end positioning method is based on the velocity difference between line mode and zero mode wave. But the zero mode wave velocity is unstable with the fault distance and the traveling wave frequency, and the error is large [6-8]. The line mode traveling wave is easy to obtain and its velocity is stable [7], from which the time of the initial wave and each reflected waves arriving at the same measuring point can be obtained, as well as the time difference between reflected waves and the initial wave. And combined with the line mode traveling wave velocity, the distance differences are obtained. As distribution network topology is known, the possible traveling paths of traveling waves are determined, and then the fault section is located. Propagation Characteristics of Fault Traveling Wave According to the superposition principle, the single phase to ground fault of the distribution line is equivalent to the fault instantaneously add a pulse signal source at the fault point, and the fault traveling wave propagates along the line to both sides of the fault point. According to the wave

Characteristics of Phase Current and its Application in Fault Section Location in Noneffectively Grounded Distribution Systems

Single-phase-to-ground Fault Detection with Distributed Parameters Analysis in Non-Direct Grounded Systems

Fault Location In Neutral Non-Effectively Grounded Distribution Systems Using Phase Current And Line-To-Line Voltage

Phase Current Based Fault Section Location for Single-Phase Grounding Fault in Non-effectively Grounded Distribution Network

Phase Current Fault Component Based Single-Phase Earth Fault Segment Location in Non-Solidly Earthed Distribution Networks

Phase Voltage and Current Fault Components Based Fault Segment Location Method Under Single-Phase Earth Fault in Distribution Network

Single-phase Earth Fault Section Location Based on Phase Current Fault Component in Distribution Network

Study for Fault Indicator Based on the Faulty Phase Current Feature Recognition for the Distribution Network

Single-phase-to-ground Fault Location Based on Transient Fault Signal and Its Attenuation Character for Distribution Network

A Novel Faulty Phase Selection Method for Single-Phase-to-Ground Fault in Distribution System Based on Transient Current Similarity Measurement

A Method of Single Phase to Ground Fault Feeder Selection Based on Single Phase Current Traveling Wave for Distribution Lines

One-Phase Ground Fault Line Selection Technology for Distribution Network Based on Comprehensive Analysis of Phase Current

Single-phase Grounding Fault Section Locating Technology for Distribution Network Based on Rough Set Algorithm

Single-phase Grounding Fault Detection Method in Resonant Grounding System Based on Phase Current Variation

Zero Sequence Current-based Fault Section Location of Distribution Network

A Faulty Section Location Method for Distribution Grid Based on Grounding Fault Transfer Device

Single Phase to Ground Fault Section Location Based on Characteristics of Traveling Wave Refraction and Reflection

Traveling-Wave Based Fault Location for Phase-to-Ground Fault in Non-Effectively Earthed Distribution Networks

Fault Location Based on Synchronous Data of Both Ends in Non-effectively Grounded System

New Method for Transient Line Selection in Distribution System Based on Grounding Fault Transferred

Single Phase Grounding Fault Location Based on Frequency Domain Characteristics of Fault Current