Abstract:Following the large‐scale integration of distributed power sources into distribution networks, fault currents undergo noticeable changes, which impacts the accuracy of conventional single‐phase ground fault algorithms. To tackle these issues, this work initially proposes an active distribution network ground fault protection algorithm based on the direction of extreme energy. Then, by establishing the electrical system structure and model of distribution network ground faults in the presence of distributed power sources, theoretical derivations and computations of transient zero‐sequence current frequency variations during fault instances are carried out. The characteristics of zero‐sequence current directions under distributed power sources integration are analysed, facilitating the design of a local ground fault determination algorithm grounded in the principle of energy extremum direction. This includes outlining fault determination and isolation procedures for ground fault monitoring equipment. Finally, through simulation testing, it is proven that the algorithm can reliably detect ground faults under both neutral point grounding configurations involving an arc suppression coil and ungrounded systems, across a range of transition resistances, varying numbers and capacities of distributed power sources connected, and differing grounding switch operation angles. After large‐scale distributed power sources are connected to the distribution network, the fault current undergoes noticeable changes, affecting the accuracy of traditional single‐phase grounding fault algorithms. Therefore, the objective of this paper is to address the impact of distributed power integration on the grounding algorithms of distribution networks. The main contribution is: by establishing an electrical system structure and model for distribution network grounding faults that include distributed generation (DG), theoretically deriving and calculating the transient zero‐sequence current frequency changes at the moment of fault, analysing the directional characteristics of zero‐sequence currents under DG connection conditions, designing a local grounding fault judgment algorithm based on energy extremum direction, and providing a fault judgment and isolation process for grounding fault monitoring devices. The results show: through simulation and experimentation, the algorithm was tested, and the method can reliably judge grounding faults under various transition resistances, different numbers and capacities of connected distributed power sources, and different grounding switch‐on angles. The applicability of the algorithm covers both methods of neutral grounding through an arc suppression coil and ungrounded neutrals, adapting to scenarios with or without DG connections.

Single-phase-to-ground Fault Detection with Distributed Parameters Analysis in Non-Direct Grounded Systems

Ground fault protection algorithm of active distribution network based on energy extremum direction

Detecting Single-Phase-to-ground Faulted Feeder in Resonant Grounded Power Distribution System

Detecting Single-Phase-to-Ground Fault Event and Identifying Faulty Feeder in Neutral Ineffectively Grounded Distribution System

A Novel Method for High Resistance Grounding Faulty Feeder Detection in Distribution Network

Research on the Countermeasures of the Single-Phase-to-earth Faults in Flexibly Grounded Distribution Networks

A data-driven method to detect and localize the single-phase grounding fault in distribution network based on synchronized phasor measurement

Faulty Phase Recognition Method for Single-Line-to-Ground Fault in Resonant Grounded Distribution Networks

A Single-Phase-to-Ground Fault Detection Method Based on the Ratio Fluctuation Coefficient of the Zero-Sequence Current and Voltage Differential in a Distribution Network

Faulty feeder detection of single phase-to-ground fault for distribution networks based on improved K-means power angle clustering analysis

Single-phase-to-ground Fault Protection for Indirect Grounding Power System

Single-phase Grounding Fault Section Locating Technology for Distribution Network Based on Rough Set Algorithm

A New Approach for Single-Phase-to-Ground Fault Detection in Mid-Voltage Systems Using Low-Voltage Sensors

High Impedance Grounding Fault Protection for Low-resistance Grounding System Based on the Ratio of Phase Active Power Variation

Machine-learning-based Single-Phase-to-ground Fault Detection in Distribution Systems

Detection of Single-Phase to Ground Faults in Low-Resistance Grounded MV Systems

Identifying Single‐phase to Ground Fault Based on Line Multi‐dimensional Data in Cyber‐physical Distribution System

A selective single-phase-to-ground fault protection for neutral un-effectively grounded systems

Faulty Feeder Detection for Single-Phase-to-Ground Fault in Distribution Networks Based on Transient Energy and Cosine Similarity

Fault line selection of single-phase to ground based on negative sequence current pilot differential in distribution network

Failure Mechanism Analysis of High Resistance Grounding Fault Protection in Distribution Network