Abstract:Numerous studies have established that coating high voltage Li battery cathode materials with a protective film can provide enhanced cycling stability and even enhance rate performance. While the exact mechanisms by which these coatings lead to enhanced performance is still not clear, it is likely that many coatings require some ability to intercalate and diffuse Li. We have therefore investigated the Li solubility and transport properties of several high performing coating materials (bulk phases), such as Al2O3, AlF3, MgO, ZrO2, SiO2, and related those properties to coating overpotential 1. Furthermore, as many coatings are just a few nanometers or fewer thick, we have also the studied the influence of interfaces between very different voltage materials on their Li intercalation properties. In our studies of coating properties and their relation to overpotential, we use ab initio density functional theory to show that the above phases, when crystalline, are very poor Li conductors except for specific directions in SiO2. We also propose an Ohmic continuum model for understanding the connection between the coating overpotential and Li solubility, diffusivity, coating thickness, and current density. We use this model and previous studies of Li in amorphous Al2O3 and AlF3 2 to predict that that Atomic Layer Deposited (ALD) Al2O3 coatings have a resistivity of 1789 MOhmm (106Ohmm), which value is qualitatively consistent with that extracted from multiple ALD experiments (ranges from 7.8 MOhmm to 913 MOhmm). The results of our Ohmic continuum model are summarized in the attached figure, which shows our predicted coating overpotential in terms of fundamental coating properties of Li solubility and diffusivity for key systems (amorphous Al2O3 and AlF3 and lithiated Li3.5Al2O3) under the condition of coating thickness L=1nm, current density J active = 0.046 mA/cm2(approximately a 1C rate) at room temperature. In order to model the effects of interfaces on the Li energetics we explore the Li intercalation energy profile across an interface of two materials with very different bulk intercalation energies. The olivine-structured FePO4-MPO4 (M=Co, Ti, Mn) and layered-structured LiNiO2-TiO2interfaces provide model cases to understand the physics governing Li intercalation energetics across material interfaces. We find that across the interface from a high to low voltage material (i.e. low to high Li intercalation energy), the Li site energy remains constant in the high voltage material and decays approximately linearly in the low voltage region, approaching the Li site energy of the low voltage material. This effect indicates that the existence of a high intercalation voltage material at an interface can significantly enhance the Li intercalation voltage in a low voltage region over a 1-2 nm scale. We explore possible implications of this interfacial voltage enhancement for the design of novel cathode superlattice structures. Figure Caption: Fig. 1 Solubility and diffusivity dependence of potential drop across a room temperature thin coating film of L = 1 nm for a current of density Jactive = 0.046 mA/cm2(approximately a 1C rate) through the active coating surface. References 1 Xu, S. et al. Lithium transport through lithium-ion battery cathode coatings. Journal of Materials Chemistry A 3, 17248-17272 (2015). 2 Hao, S. Q. & Wolverton, C. Lithium Transport in Amorphous Al2O3 and AlF3 for Discovery of Battery Coatings. J. Phys. Chem. C 117, 8009-8013, (2013). Figure 1

Unraveling the LiNbO3 Coating Layer on Battery Performances of Lithium Argyrodite-Based All-Solid-state Batteries under Different Cut-off Voltages

Enabling superior cathode/sulfide electrolyte interfacial stability by Li3BO3 coating for all solid-state Li battery

LiNbO3 and LiTaO3 Coating Effects on the Interface of the LiCoO2 Cathode: A DFT Study of Li-Ion Transport

Manipulating interfacial stability of LiNi0.5Co0.3Mn0.2O2 cathode with sulfide electrolyte by nanosized LLTO coating to achieve high-performance all-solid-state lithium batterie

Quantifying the Local Li-ion Diffusion over the Grain Boundaries of a Protective Coating, Revealing the Impact on the Macroscopic Li-ion Transport in an All-Solid-state Battery

Enhanced all-solid-state battery performance through in-situ construction of interface modification layer

Quantification of the Li-ion Diffusion over an Interface Coating in All-Solid-state Batteries Via NMR Measurements

Microscopic Segregation Dominated Nano‐Interlayer Boosts 4.5 V Cyclability and Rate Performance for Sulfide‐Based All‐Solid‐State Lithium Batteries

Theoretical Modeling of Protective Cathode Coatings and Cathode/Coating Interfaces in Li-Ion Batteries

Control of Lattice Orientation and Interface of LiCoO2 for All Solid State Batteries

Enabling Structural and Interfacial Stability Via Coherent Interface Li3BO3 Coating for Lithium-Rich Manganese-Based Cathodes

Advancing Lithium-Ion Batteries' Electrochemical Performance: Ultrathin Alumina Coating on Li(Ni0.8Co0.1Mn0.1)O2 Cathode Materials

Enhanced High-Voltage Cycling Stability of Ni-rich LiNi0.8Co0.1Mn0.1O2 Cathode Coated with Li2O–2B2O3

Impact of Amorphous LiF Coating Layers on Cathode‐Electrolyte Interfaces in Solid‐State Batteries

Suppress voltage decay of lithium-rich materials by coating layers with different crystalline states

Li7La3Zr2O12-co-LiNbO3 Surface Modification Improves the Interface Stability between Cathode and Sulfide Solid-State Electrolyte in All-Solid-State Batteries

Engineering Stable Decomposition Products on Cathode Surfaces to Enable High Voltage All‐Solid‐State Batteries

Understanding the Effects of Surface Modification on Improving the High-Voltage Performance of Ni-rich Cathode Materials

Effect of surface carbonates on the cyclability of LiNbO3-coated NCM622 in all-solid-state batteries with lithium thiophosphate electrolytes

Beneficial Effects of La0.5Sr0.5CoO3 Coatings on Thin‐Film LiMn2O4 Cathodes for Lithium Ion Batteries

Investigation on the Overlithiation Mechanism of LiCoO 2 Cathode for Lithium Ion Batteries