Abstract:Numerous studies have established that coating high voltage Li battery cathode materials with a protective film can provide enhanced cycling stability and even enhance rate performance. While the exact mechanisms by which these coatings lead to enhanced performance is still not clear, it is likely that many coatings require some ability to intercalate and diffuse Li. We have therefore investigated the Li solubility and transport properties of several high performing coating materials (bulk phases), such as Al2O3, AlF3, MgO, ZrO2, SiO2, and related those properties to coating overpotential 1. Furthermore, as many coatings are just a few nanometers or fewer thick, we have also the studied the influence of interfaces between very different voltage materials on their Li intercalation properties. In our studies of coating properties and their relation to overpotential, we use ab initio density functional theory to show that the above phases, when crystalline, are very poor Li conductors except for specific directions in SiO2. We also propose an Ohmic continuum model for understanding the connection between the coating overpotential and Li solubility, diffusivity, coating thickness, and current density. We use this model and previous studies of Li in amorphous Al2O3 and AlF3 2 to predict that that Atomic Layer Deposited (ALD) Al2O3 coatings have a resistivity of 1789 MOhmm (106Ohmm), which value is qualitatively consistent with that extracted from multiple ALD experiments (ranges from 7.8 MOhmm to 913 MOhmm). The results of our Ohmic continuum model are summarized in the attached figure, which shows our predicted coating overpotential in terms of fundamental coating properties of Li solubility and diffusivity for key systems (amorphous Al2O3 and AlF3 and lithiated Li3.5Al2O3) under the condition of coating thickness L=1nm, current density J active = 0.046 mA/cm2(approximately a 1C rate) at room temperature. In order to model the effects of interfaces on the Li energetics we explore the Li intercalation energy profile across an interface of two materials with very different bulk intercalation energies. The olivine-structured FePO4-MPO4 (M=Co, Ti, Mn) and layered-structured LiNiO2-TiO2interfaces provide model cases to understand the physics governing Li intercalation energetics across material interfaces. We find that across the interface from a high to low voltage material (i.e. low to high Li intercalation energy), the Li site energy remains constant in the high voltage material and decays approximately linearly in the low voltage region, approaching the Li site energy of the low voltage material. This effect indicates that the existence of a high intercalation voltage material at an interface can significantly enhance the Li intercalation voltage in a low voltage region over a 1-2 nm scale. We explore possible implications of this interfacial voltage enhancement for the design of novel cathode superlattice structures. Figure Caption: Fig. 1 Solubility and diffusivity dependence of potential drop across a room temperature thin coating film of L = 1 nm for a current of density Jactive = 0.046 mA/cm2(approximately a 1C rate) through the active coating surface. References 1 Xu, S. et al. Lithium transport through lithium-ion battery cathode coatings. Journal of Materials Chemistry A 3, 17248-17272 (2015). 2 Hao, S. Q. & Wolverton, C. Lithium Transport in Amorphous Al2O3 and AlF3 for Discovery of Battery Coatings. J. Phys. Chem. C 117, 8009-8013, (2013). Figure 1

LiNbO3 and LiTaO3 Coating Effects on the Interface of the LiCoO2 Cathode: A DFT Study of Li-Ion Transport

Enhanced Electrochemical Performance of LiNi0.8Co0.15Al0.05O2 Cathode Material via Li2TiO3 Nanoparticles Coating

Unraveling the LiNbO3 Coating Layer on Battery Performances of Lithium Argyrodite-Based All-Solid-state Batteries under Different Cut-off Voltages

High-voltage Performance of LiCoO2 Cathode Studied by Single Particle Microelectrodes –influence of Surface Modification with TiO2

On the Active Components in Crystalline Li-Nb-O and Li-Ta-O Coatings from First Principles

On the Active Components in Crystalline Li–Nb–O and Li–Ta–O Coatings from First Principles

Theoretical Modeling of Protective Cathode Coatings and Cathode/Coating Interfaces in Li-Ion Batteries

Ta doping and LiTaO3 coating to improve the electrochemical performance of LiNi0.925Co0.03Mn0.045O2 cathode material for lithium ion batteries

Effect of TiO 2 -Coating on Structure and Electrochemical Performance of LiCo 0.2 Ni 0.4 Mn 0.4 O 2

Control of Lattice Orientation and Interface of LiCoO2 for All Solid State Batteries

Manipulation of an ionic and electronic conductive interface for highly-stable high-voltage cathodes

Enhanced Interfacial Kinetics and High-Voltage/High-Rate Performance of Licoo2 Cathode by Controlled Sputter-Coating with A Nanoscale Li4ti5o12 Ionic Conductor

Enhanced Cycling Stability of Microsized Licoo2 Cathode by Li4ti5o12 Coating for Lithium Ion Battery

Impact of Amorphous LiF Coating Layers on Cathode‐Electrolyte Interfaces in Solid‐State Batteries

Roles of Fast-Ion Conductor LiTaO3 Modifying Ni-rich Cathode Material for Li-Ion Batteries

Effects of SrO/Li_2O/La_2O_3/Ta_2O_5/TiO_2-coating on Electrochemical Performance of LiCoO_2

Effect of TiC surface oxide overlayer on the control of Li O behavior in lithium-oxygen batteries: Implications for cathode catalyst design

Enabling superior cathode/sulfide electrolyte interfacial stability by Li3BO3 coating for all solid-state Li battery

Effects of co-coating La2O3 and TiO2 on tissue morphology and electrochemical properties of LiMn2O4 cathode materials

Beneficial Effects of La0.5Sr0.5CoO3 Coatings on Thin‐Film LiMn2O4 Cathodes for Lithium Ion Batteries

Effect of surface carbonates on the cyclability of LiNbO3-coated NCM622 in all-solid-state batteries with lithium thiophosphate electrolytes