Abstract:Sulfide-based all-solid-state Li-ion batteries (ASSLIBs) are recognized as promising next-generation batteries, due to its advantage of high energy density, high safety and high Li+ diffusivity in sulfide solid electrolytes (SEs). However, interfacial instability between cathode (like LiCoO2) and sulfide SEs hinders its commercial applica-tions. Herein, a simple mechanochemical strategy, which mechanically mixed polyanionic borate precursor and Li2CO3 residue on LiCoO2 (LCO) cathode with subsequent thermochemical reactions, was proposed to achieve analogous "solid electrolyte interphase (SEI)" to address such issues. The artificial SEI consists of crystalline LiBa (B3O5)3 (LBBO), Li3BO3 (LBO) and amorphous lithium boron oxide (Li-B-O). Therein, the former two endow high interfacial stability with SEs and ionic conductivity respectively, while the latter presented in the former interspace isolated the LCO cathode from Li10GeP2S12 (LGPS) solid electrolyte and constructed a continuous interlayer with LBBO and LBO. According to the phase diagram and direct observation through TEM, it is confirmed that a suitable ratio of raw LBBO precursor and Li2CO3 residue can realize an appropriate proportion of LBO to balance the interfacial stability and the diffusion of Li+ in obtained artificial interlayer, which enables high cyclability and rate performance in LCO/LGPS/Li-In ASSLIBs. Specifically, SEI with 9.4 mol.% LBO boosts an initial discharge capacity of 153.8 mAh g+1 (2.6-4.3 V (vs. Li/Li+), 0.1 C) with 74.4 % retention (150 cycles) and an excellent rate capability of 92.9 and 56.1 mAh g+1 at 1 C and 2 C respectively. Upon increased cut-off voltage of 4.5 V, an initial 167.3 mAh g+1 capacity (0.2 C) and 64.7 % retention (150 cycles) can also be ach-ieved. The present strategy utilizing mechanochemical reactions between polyanionic borate and Li2CO3 residue to construct analogous SEI will offer fresh insights to stabilize the electrode/electrolyte interface of ASSLIBs derived from diverse polyanionic-type borates or phosphates, which can be widely used in other all-solid-state batteries with various cathodes and electrolytes.

Enabling superior cathode/sulfide electrolyte interfacial stability by Li3BO3 coating for all solid-state Li battery

Enabling Structural and Interfacial Stability Via Coherent Interface Li3BO3 Coating for Lithium-Rich Manganese-Based Cathodes

Li7La3Zr2O12-co-LiNbO3 Surface Modification Improves the Interface Stability between Cathode and Sulfide Solid-State Electrolyte in All-Solid-State Batteries

Manipulating interfacial stability of LiNi0.5Co0.3Mn0.2O2 cathode with sulfide electrolyte by nanosized LLTO coating to achieve high-performance all-solid-state lithium batterie

Understanding the Role of Lithium Borate as the Surface Coating on High Voltage Single Crystal LiNi0.5Mn1.5O4

Interdiffusion suppression at the cathode‐electrolyte interface of all‐solid‐state‐batteries by Li3PO4 conformal coating

Surface coating with Li3BO3 protection layer to enhance the electrochemical performance and safety properties of Ni-rich LiNi0.85Co0.05Mn0.10O2 cathode material

Enhanced all-solid-state battery performance through in-situ construction of interface modification layer

(Digital Presentation) Simultaneous Transforming Residual Lithium Compounds and Stabilizing Surface Lattice Oxygen for Ni-Rich Cathode Via Atomic Layer Deposition and Post-Annealing

Lanthanum doping and surface Li 3 BO 3 passivating layer enabling 4.8 V nickel-rich layered oxide cathodes toward high energy lithium-ion batteries

Outstanding electrochemical performances of the all-solid-state lithium battery using Ni-rich layered oxide cathode and sulfide electrolyte

Mechanochemical Reactions Between Polyanionic Borate and Residue Li2CO3 on LiCoO2 to Stabilize Cathode/electrolyte Interface in Sulfide-Based All-Solid-state Batteries

Microscopic Segregation Dominated Nano‐Interlayer Boosts 4.5 V Cyclability and Rate Performance for Sulfide‐Based All‐Solid‐State Lithium Batteries

Improving the Interfacial Stability of Ultrahigh-Nickel Cathode with PEO-based Electrolyte by Targeted Chemical Reactions

Nanoscale operation of Ni-Rich cathode surface by polycrystalline solid electrolytes Li3.2Zr0.4Si0.6O3.6 coating

Enhanced cycling stability of single-crystal LiNi0.83Co0.07Mn0.10O2 by Li-reactive coating with H3BO3

High-performance LiNi0.8Mn0.1Co0.1O2 cathode by nanoscale lithium sulfide coating via atomic layer deposition

Engineering Stable Decomposition Products on Cathode Surfaces to Enable High Voltage All‐Solid‐State Batteries

Stabilized Cathode/Sulfide Electrolyte Interface through Conformally Interfacial Nanocoating for All-Solid-State Batteries

"Win‐Win" Modification of LiCoO2 Enables Stable and Long‐Life Cycling of Sulfide‐Based All Solid‐State Batteries

A Novel Perovskite Electron-Ion Conductive Coating to Simultaneously Enhance Cycling Stability and Rate Capability of Li1.2Ni0.13Co0.13Mn0.54O2 Cathode Material for Lithium-Ion Batteries