Abstract:A nanoscale Li+ conductive interlayer Li1.175Nb0.645Ti0.4O3 is coated at the LiCoO2 surface and used in sulfide‐based all solid‐state lithium batteries (ASSLBs). With better σLi+ and microscopic segregation of Ti and Nb during the cycling process, the interlayer stabilizes the cathode lattice and simultaneously mitigates the side reactions. Therefore, ASSLBs can cycle under 4.5 V and show excellent cyclability and rate performance. To implement the growing requirement for higher energy density all‐solid‐state lithium batteries (ASSLBs), further increasing the working voltage of LiCoO2 (LCO) is a key to breaking through the bottleneck. However, LiCoO2 severe structural degradation and side reactions at the cathode interface obstruct the development of high‐voltage sulfide‐based ASSLBs (≥4.5 V). Herein, a nano‐metric Li1.175Nb0.645Ti0.4O3 (LNTO) coated LCO cathode where microscopic Ti and Nb segregation at the interface during cycling potentially stabilizes the cathode lattice, and minimizes side reactions, simultaneously, is designed. Advanced transmission electron microscopy reveals that the stable spinel phase minimizes the micro stress at the cathode interface, avoids structure fragmentation, and hence significantly enhances the long‐term cyclic stability of LNTO@LCO @ 4.5 V. Moreover, the differential phase contrast scanning transmission electron microscopy (DPC‐STEM) visualizes the nano‐interlayer LNTO to boost Li+ migration at the cathode interface. Electrochemical impedance spectroscopy (EIS) reveals that sulfide‐based cells with the LNTO nano‐layer effectively reduce the interfacial resistance to 140 Ω compared to LiNbO3 (235 Ω) over 100 cycles. Therefore, 4.5 V sulfide‐based ASSLBs offer gratifying long‐cycle stability (0.5 C for 1000 cycles, 88.6%), better specific capacity, and rate performance (179.8 mAh g–1 at 0.1 C, 97 mAh g–1 at 2 C).

Manipulating interfacial stability of LiNi0.5Co0.3Mn0.2O2 cathode with sulfide electrolyte by nanosized LLTO coating to achieve high-performance all-solid-state lithium batterie

Stabilized Cathode/Sulfide Electrolyte Interface through Conformally Interfacial Nanocoating for All-Solid-State Batteries

High Performance Single-Crystal Ni-Rich Cathode Modification via Crystalline LLTO Nanocoating for All-Solid-State Lithium Batteries

A Dynamically Stable Sulfide Electrolyte Architecture for High-Performance All-Solid-State Lithium Metal Batteries

High-Performance Sulfide All-Solid-State Batteries Enabled by High-Voltage Ni-Rich Cathode with a Conformal and Conductive Protective Layer

Surface-modified and sulfide electrolyte-infiltrated LiNi0.6Co0.2Mn0.2O2 cathode for all-solid-state lithium batteries

Slurry-Coated LiNi0.8Co0.1Mn0.1O2-Li3InCl6 Composite Cathode with Enhanced Interfacial Stability for Sulfide-Based All-Solid-State Batteries.

Outstanding electrochemical performances of the all-solid-state lithium battery using Ni-rich layered oxide cathode and sulfide electrolyte

Microscopic Segregation Dominated Nano‐Interlayer Boosts 4.5 V Cyclability and Rate Performance for Sulfide‐Based All‐Solid‐State Lithium Batteries

Constructing rapid ionic transfer layer to boost the performance of LiCoO2 cathode with high mass loading for all-solid-state lithium battery

Unraveling Interfacial Compatibility of Ultrahigh Nickel Cathode and Chloride Solid Electrolyte for Stable All-Solid-state Lithium Battery

Unraveling the interfacial compatibility of ultrahigh nickel cathodes and chloride solid electrolyte for stable all-solid-state lithium batteries

Magicking an oxyhalide interface for 4.8 V‐tolerant high‐nickel cathodes in all‐solid‐state lithium‐ion batteries

Chemo-mechanical stable cathode interphase via interface in-situ catalytic-conversion integrated design for all solid-state batteries

Stabilization of Li0.33La0.55TiO3 Solid Electrolyte Interphase Layer and Enhancement of Cycling Performance of LiNi0.5Co0.3Mn0.2O2 Battery Cathode with Buffer Layer

Single-Crystal-Layered Ni-Rich Oxide Modified by Phosphate Coating Boosting Interfacial Stability of Li10 SnP2 S12 -Based All-Solid-State Li Batteries.

Enabling superior electrochemical performance of NCA cathode in Li5.5PS4.5Cl1.5-based solid-state batteries with a dual-electrolyte layer

Origin and regulation of interfacial instability for nickel-rich cathodes and NASICON-type Li1+xAlxTi2−x(PO4)3 solid electrolytes in solid-state lithium batteries

Interphase Stabilization of LiNi0.5 Mn1.5 O4 Cathode for 5 V-Class All-Solid-State Batteries

Dual modified NCMA cathode with enhanced interface stability enabled high-performance sulfide-based all-solid-state lithium battery

Surface Construction of a High-Ionic-Conductivity Buffering Layer on a LiNi<sub>0.6</sub>Co<sub>0.2</sub>Mn<sub>0.2</sub>O<sub>2</sub> Cathode for Stable All-Solid-State Sulfide-Based Batteries