Abstract:All-solid-state batteries employing sulfide solid electrolyte and Li metal anode are promising because of their high safety and energy densities. However, the interface between Li metal and sulfides suffers from catastrophic instability which stems the practical use. Here, a dynamically stable sulfide electrolyte architecture to construct the hierarchy of interface stability is reported. By rationally designing the multilayer structures of sulfide electrolytes, the dynamic decomposing-alloying process from MS4 (M = Ge or Sn) unit in sulfide interlayer can significantly prohibit Li dendrite penetration is revealed. The abundance of highly electronic insulating decompositions, such as Li2S, at the sulfide interlayer interface helps to well constrain the dynamic decomposition process and preserve the long-term polarization stability is also highlighted. By using Li6PS5Cl||Li10SnP2S12||Li6PS5Cl electrolyte architecture, Li metal anode shows an unprecedented critical current density over 3 mA cm-2 and achieves the steady over-potential for approximate to 900 hours. Based upon the merits, the Li||LiNi0.8Co0.1Mn0.1O2 battery delivers a remarkable 75.3% retention even after 600 cycles at 1 C (1C-0.95 mA cm-2) under a low stack pressure of 15 MPa. A universal dynamically stable multilayer sulfide electrolyte to inhibit dendrite and stabilize polarization is reported. It is revealed that the dynamic decomposing-alloying process by the HVMEC-SSE interlayer prohibits dendrite penetration. Li anode shows an unprecedented critical current density over 3 mA cm-2 and holds the steady over-potential for approximate to 900 h. This work provides insights into understanding the hierarchy of interface stabilities.image

Single-Crystal-Layered Ni-Rich Oxide Modified by Phosphate Coating Boosting Interfacial Stability of Li10 SnP2 S12 -Based All-Solid-State Li Batteries.

Stabilized Cathode/Sulfide Electrolyte Interface through Conformally Interfacial Nanocoating for All-Solid-State Batteries

High-Performance Sulfide All-Solid-State Batteries Enabled by High-Voltage Ni-Rich Cathode with a Conformal and Conductive Protective Layer

Manipulating interfacial stability of LiNi0.5Co0.3Mn0.2O2 cathode with sulfide electrolyte by nanosized LLTO coating to achieve high-performance all-solid-state lithium batterie

Surface-modified and sulfide electrolyte-infiltrated LiNi0.6Co0.2Mn0.2O2 cathode for all-solid-state lithium batteries

A Dynamically Stable Sulfide Electrolyte Architecture for High-Performance All-Solid-State Lithium Metal Batteries

Origin and regulation of interfacial instability for nickel-rich cathodes and NASICON-type Li1+xAlxTi2−x(PO4)3 solid electrolytes in solid-state lithium batteries

High Performance Single-Crystal Ni-Rich Cathode Modification via Crystalline LLTO Nanocoating for All-Solid-State Lithium Batteries

Recent Advances in Li1+xAlxTi2−x(PO4)3 Solid-State Electrolyte for Safe Lithium Batteries

A Plastic-Crystal Electrolyte Layer Promotes Interfacial Stability of Ni-Rich Oxide Cathode in Li6PS5Cl-Based All-Solid-State Rechargeable Li Batteries

Slurry-Coated LiNi0.8Co0.1Mn0.1O2-Li3InCl6 Composite Cathode with Enhanced Interfacial Stability for Sulfide-Based All-Solid-State Batteries.

Li7La3Zr2O12-co-LiNbO3 Surface Modification Improves the Interface Stability between Cathode and Sulfide Solid-State Electrolyte in All-Solid-State Batteries

Slurry-Coated LiNi 0.8 Co 0.1 Mn 0.1 O 2 -Li 3 InCl 6 Composite Cathode with Enhanced Interfacial Stability for Sulfide-Based All-Solid-State Batteries

Outstanding electrochemical performances of the all-solid-state lithium battery using Ni-rich layered oxide cathode and sulfide electrolyte

Dual-functional interfaces for highly stable Ni-rich layered cathodes in sulfide all-solid-state batteries

Interfacial Stability of Phosphate-NASICON Solid Electrolytes in Ni-Rich NCM Cathode-Based Solid-State Batteries

Enhanced Electrochemical Stability and Extended Cycle Life in Sulfide-Based All-Solid-State Batteries: The Role of Li10 SnP2 S12 Coating on Ni-Rich NCM Cathode

Designing the Interface Layer of Solid Electrolytes for All‐Solid‐State Lithium Batteries

Interphase Stabilization of LiNi0.5 Mn1.5 O4 Cathode for 5 V-Class All-Solid-State Batteries

Constructing rapid ionic transfer layer to boost the performance of LiCoO2 cathode with high mass loading for all-solid-state lithium battery

A Catalyst SnO2 Improves the Performance of All-Solid-State Batteries with LiNi0.5Mn1.5o4@SnO2 Cathodes, Pmma-Pvdf@ Li1.3ai0.3ti1.7(Po4)3 Composite Solid Electrolyte and Lithium Metal Anodes