Abstract:The lithium-ion battery has the advantages of high energy density, long service life, and good safety performance, and is used as an ideal energy storage device. Cobalt-free lithium-rich manganese cathode materials have attracted much attention due to their high specific capacity and low cost. However, its poor cycling performance is not conducive to practical application. So far, researchers have mainly addressed this problem with surface coatings. In this study, spinel Li4Mn5O12 was successfully prepared by wet chemical method to modify the surface of Li1.2Ni0.2Mn0.6O2. The X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) test results showed that the crystal structure of the samples did not change significantly, but the cationic order was improved. The results of the scanning electron microscope (SEM), energy dispersive spectrometer (EDS), and transmission electron microscope (TEM) showed that an ultrathin spinel Li4Mn5O12 surface-modified layer with a thickness of about 10 nm was successfully constructed on the raw material surface. In addition, the lithium-ion diffusion coefficients (DLi+) of the raw materials and modified materials were calculated by electrochemical impedance spectroscopy (EIS) test and impedance fitting. The results indicated that the ultrathin Li4Mn5O12 surface modification shell can increase the lithium-ion diffusion rate of the material and improve the rate capability of the material. So, the results show that the surface modification layer of spinel Li4Mn5O12 can reduce the oxygen loss of the first cycle and improve the cationic order of the material. Therefore, the first coulombic efficiency of Li4Mn5O12/Li1.2Ni0.2Mn0.6O2 material at the current density of 12.5 mA×g-1 reaches 80.46%, and the capacity retention rate reaches 91.74% after 50 cycles, which is 3.36% and 21.23% higher than that of the raw materials, respectively. It showed better electrochemical reversibility and cyclic stability. This study provides a straightforward and convenient modification method for improving the stability of cobalt-free lithium-rich manganese cathode materials and has a favorable application prospect.

Enabling Structural and Interfacial Stability Via Coherent Interface Li3BO3 Coating for Lithium-Rich Manganese-Based Cathodes

Enhanced Structural Stability and Durability in Lithium-Rich Manganese-Based Oxide Via Surface Double-Coupling Engineering

Modulating Surface Architecture and Electronic Conductivity of Li-rich Manganese-Based Cathode

Building interface bonding and shield for stable Li-rich Mn-based oxide cathode

Enhanced Cycling Stability of Lithium-Rich Cathode Materials Achieved by in-situ Formation of LiErO2 Coating

Recent advance in coating strategies for lithium-rich manganese-based cathode materials

Constructing a robust integrated surface structure for enhancing the performance of Li-rich Mn-based oxides cathodes

Simultaneous dual modification of Li-rich Mn-based cathode in restraining oxygen release and structure distortion

Achieving high initial coulombic efficiency and low voltage dropping in Li-rich Mn-based cathode materials by Metal-Organic frameworks-derived coating

One-pot synthesis and multifunctional surface modification of lithium-rich manganese-based cathode for enhanced structural stability and low-temperature performance

Multi-functionalized Full-Interface Integrated Engineering Towards Highly Reversible Li-rich Mn-based Cathode

Multifunctional surface structure with enhanced electron and ion conductivities for superior electrochemical performance of Co-free Li-rich Mn-based layered oxide cathodes

Large-scale Synthesis of Lithium- and Manganese-Rich Materials with Uniform Thin-Film Al 2 O 3 Coating for Stable Cathode Cycling

Enabling structural and interfacial stability of 5 V spinel LiNi0.5Mn1.5O4 cathode by a coherent interface

Buliding Ultrathin Li4mn5o12 Shell for Enhancing the Stability of Cobalt-Free Lithium-Rich Manganese Cathode Materials

Enhanced Cycling Stability of Single-Crystal LiNi 0.83 Co 0.07 Mn 0.10 O 2 by Li-reactive Coating with H 3 BO 3

Enabling superior cathode/sulfide electrolyte interfacial stability by Li3BO3 coating for all solid-state Li battery

Enhancing cycling stability in Li-rich Mn-based cathode materials by solid-liquid-gas integrated interface engineering

Surface modification of boron cobalt complexes to enhance cycling performance of cobalt-free Li-rich cathode materials

Understanding Boron Chemistry as the Surface Modification and Electrolyte Additive for Co-free Lithium-Rich Layered Oxide

Synergistic Enhancement of Li-rich Manganese-based Cathode Materials through Single Crystallization and In-situ Spinel Coating