Abstract:To enhance the electrochemical properties and safety performance of Ni-rich cathode materials for Lithium-ion batteries, a typical wet chemical method followed by high temperature sintering was applied to make the Li+ conductive Li3BO3 with different mass fractions cover on the surface of Ni-rich LiNi0.85Co0.05Mn0.10O2. And the influence of the coating layer on the phase, crystal structure, particles morphology and electrochemical properties during cycling were systematically studied. The physicochemical characterization results suggested a coating layer with a thickness of 10–15 nm formed by Li3BO3 nanoparticles was equably adhered on the surface of cathode particles, without causing obvious variation of the crystal structure and morphology. The electrochemical measurement indicated the suitable amount of Li3BO3 coating layer could effectively enhance the rate capability, discharge ability at low temperature and cycling performance of LiNi0.85Co0.05Mn0.10O2 due to the increased Li+ diffusion rate and restrained side reaction from electrode with electrolyte. Particularly, the 2 wt% Li3BO3 coated LiNi0.85Co0.05Mn0.10O2 respectively delivered a capacity retention of 91.4% and 90.1% at 25 °C and 45 °C after 300 cycles, and the pristine one merely retained a capacity retention of 83.9% and 80.4% accordingly. Besides, the pouch full batteries with 2 wt% Li3BO3 coated LiNi0.85Co0.05Mn0.10O2 cathode demonstrated the obvious enhancement on the safety properties and storage performance when compared to the pristine one for the pouch batteries

Enhanced cycling stability of single-crystal LiNi0.83Co0.07Mn0.10O2 by Li-reactive coating with H3BO3

Enhanced Electrochemical Performance of LiNi0.8Co0.15Al0.05O2 Cathode Material via Li2TiO3 Nanoparticles Coating

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Realizing Superior Cycling Stability of Ni-Rich Layered Cathode by Combination of Grain Boundary Engineering and Surface Coating

Tuning the surface of LiNi0.8Co0.1Mn0.1O2 primary particle with lithium boron oxide toward stable cycling

Sol/Antisolvent Coating for High Initial Coulombic Efficiency and Ultra-stable Mechanical Integrity of Ni-Rich Cathode Materials

Improving Electrochemical Cycling Stability of Ni‐rich LiNi0.91Co0.06Al0.03O2 Cathode Materials Through H3BO3 and Y2O3 Composite Coating

Excellent electrochemical properties of Ni-rich LiNi0.88Co0.09Al0.03O2 cathode materials co-modified with Mg-doping and LiBO2-coating for lithium ion battery

Surface Coating with Li-Ti-O to Improve the Electrochemical Performance of Ni-rich Cathode Material

Surface coating with Li3BO3 protection layer to enhance the electrochemical performance and safety properties of Ni-rich LiNi0.85Co0.05Mn0.10O2 cathode material

Enhanced High-Voltage Cycling Stability of Ni-rich LiNi0.8Co0.1Mn0.1O2 Cathode Coated with Li2O–2B2O3

LiNbO3 Coating and F- Doping Stabilize the Crystal Structure and Ameliorate the Interface of LiNi0.88Co0.06Mn0.03Al0.03O2 to Improve the Electrochemical Properties and Safety Capability

Inverse Spinel-Structured Mg2MnO4 Coating to Enable Superior Thermal Stability of LiNi0.83Co0.12Mn0.05O2 Cathodes for Lithium-Ion Batteries

Enhanced structure and electrochemical stability of single crystal nickel-rich cathode material by La2Li0.5Co0.5O4 surface coating

Improving Electrochemical Cycling Stability of Ni‐rich LiNi 0.91 Co 0.06 Al 0.03 O 2 Cathode Materials through H 3 BO 3 and Y 2 O 3 Composite Coating

Dual-Element-Modified Single-Crystal LiNi0.6Co0.2Mn0.2O2 As a Highly Stable Cathode for Lithium-Ion Batteries.

One-Step Synthesis of a Single-Crystal LiNi 0.83 Co 0.11 Mn 0.06 O 2 Cathode with Excellent Electrochemical Properties by Ti 4+ Doping and LiTi 2 O 4 In Situ Chemical Coating Using a Novel Variable Temperature Sintering Process

Improving the Electrochemical Performance of Ni-rich Cathode Material LiNi 0.815 Co 0.15 Al 0.035 O 2 by Removing the Lithium Residues and Forming Li 3 PO 4 Coating Layer

Investigation of Li 3 PO 4 Coating and Nb 5+ Doping Effect on the Crystal Structure and Electrochemical Properties of Ni-Rich LiNi 0.85 Co 0.05 Mn 0.10 O 2 Cathode

Removing lithium residues via H3BO3 washing and concurrent in-situ formation of a lithium reactive coating on Ni-rich cathode materials toward enhanced electrochemical performance

A Low-Temperature Coating Method with H3BO3 for Enhanced Electrochemical Performance of Ni-rich LiNi0.82Co0.12Mn0.06O2 Cathode