Abstract:The deformation mechanisms that dictate the tribological performances of heat treated Ni55Ti45, Ni54Ti45Hf1 and Ni56Ti36Hf8 alloys are revealed through rolling contact fatigue (RCF) testing and transmission electron microscopy (TEM) analyses. Analysis of worn samples that passed a 5×108 cycle RCF runout condition shows that damage is primarily confined to deformation bands that propagate several hundred nanometers – to – several microns beneath the surface. These bands nucleate via localization of dislocation slip within the B2 austenite phase of the alloys. For the Ni55Ti45 and Ni54Ti45Hf1 samples, further damage and eventual spall failures occur by shearing and dissolution of the strengthening Ni4Ti3 nanoprecipitates within the deformation bands, followed by nanocrystallization that sometimes includes stress-induced nucleation of B19′ nanocrystals. Eventually, complete amorphization occurs prior to fracture. The relative 15 – 25% increase in RCF contact stress performance of the Ni56Ti36Hf8 alloy correlates with a more limited depth of damaged material beneath the wear surface; heavily damaged material beneath spall failure sites only extends 1.5 µm into the sample, compared to > 6 µm for Ni55Ti45 and Ni54Ti45Hf1 alloys. This superior RCF damage resistance of the Ni56Ti36Hf8 alloy results from a lower fraction of B2 matrix phase (≤ 13 %) that is highly confined by both cubic Ni-rich NiTiHf and H-phase nanoprecipitates. Specifically, this microstructure limits the widths of deformation bands within the B2 austenite phase to less than the size of the strengthening nanoprecipitates, which in turn inhibits precipitate shearing and dissolution processes that precede nanocrystallization and amorphization.

Rolling-sliding contact fatigue failure and associated evolutions of microstructure, crystallographic orientation and residual stress of AISI 9310 gear steel

Rolling contact fatigue and damage characteristic of AISI 9310 steel with pre-laser shock peening treatment

Microstructural-based analysis of the unexpected differences in rolling contact fatigue behavior between SAE52100 and SAE4320

Fatigue and recrystallization evolution of carbide-free bainitic layer under high-stress rolling sliding contact

The origin of microstructural alterations in M50 bearing steel undergoing rolling contact fatigue

Finite Element Analysis Simulation of the Effect of Induction Hardening on Rolling Contact Fatigue

Investigation on Rolling Contact Fatigue of 55 Medium-Carbon Steel

Influence of original microstructure on rolling contact fatigue property of D2 wheel steel

The effect of retained austenite on rolling/sliding contact fatigue of high carbon steel

Fatigue behaviors of ultrasonic surface rolling processed AISI 1045: the role of residual stress and gradient microstructure

Bending Fatigue Behaviour and Fatigue Endurance Limit Prediction of 20Cr2Ni4A Gear Steel after the Ultrasonic Surface Rolling Process

An electron backscatter diffraction investigation on microstructural evolution of pearlite wheel steel near rolling contact fatigue crack tip

Analysis of the Influence of Contact Stress on the Fatigue of AD180 High-Carbon Semi-Steel Roll

Crystal plasticity modeling of grain boundary softening and fatigue in U75V pearlite steel under low strain conditions: A study of cyclic rolling contact fatigue

A study on the of rolling contact fatigue mechanism of ZC-L cast wheel steel

Increasing Fatigue Life of 09Mn2Si Steel by Helical Rolling: Theoretical-Experimental Study on Governing Role of Grain Boundaries

Further Investigations and Parametric Analysis of Microstructural Alterations under Rolling Contact Fatigue

Rolling contact fatigue deformation mechanisms of nickel-rich nickel-titanium-hafnium alloys

Investigation into Rolling Contact Fatigue Performance of Aerospace Bearing Steels

Analysis of flow stress and microstructure evolution of 9310 steel during the hot compression

Rolling contact fatigue failure mechanism of bearing steel on different surface roughness levels under heavy load