Abstract:Roughly 75% of the cost for Lithium ion batteries are attributed to material cost for electrodes, electrolyte and separator. Furthermore, the production cost of the cathode material is responsible for >50% of the overall material cost. Therefore, technological breakthroughs for an increased energy density and decreased production cost along the whole battery value chain are urgently needed. State of the art (SOTA) cathode active materials (CAMs) are LiFePO 4 (LFP) and layered oxides such as LiNi 1-x-y Co x Mn y O 2 (NCM). By increasing the Ni content within NCM materials, the discharge capacity and therefore the energy density on material level can be gradually increased. Since a higher Ni content (>80% Ni) in NCM ́s implicitly entails several challenges with respect to the material synthesis procedure, stability during electrode processing as well as life time, the broad commercialization of these CAMs still needs further advances. Aqueous processing of Ni-rich layered oxide cathode materials is a promising approach to simultaneously decrease electrode manufacturing costs, while bringing environmental benefits by substituting the SOTA, often toxic and expensive organic processing solvents. Furthermore, recycling of batteries and especially of the cathode material, will probably become an important topic in the coming years. The conversion of electrodes into black mass might be cheaper and easier for aqueously-processed cathodes ( e . g ., by using fluorine-free binders). However, an aqueous environment still remains challenging due to the high reactivity of Ni-rich layered oxides towards moisture, leading to surface reconstruction, lithium leaching and Al current collector corrosion due to the resulting high pH value of the aqueous electrode paste. Common approaches to suppress current collector corrosion are the protection of the Al current collector by a carbon coating or decreasing the pH value by using dilute acids. The latter approach, especially with phosphoric acid, might lead to formation of a phosphate coating at the surface of cathode particles, which is able to protect the NCM against further degradation. Herein, we present a facile method to enable aqueous processing of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) by the addition of lithium sulphate (Li 2 SO 4 ) during electrode paste dispersion. The aqueously-processed electrodes retain 80% of their initial capacity after 400 cycles in NCM811 || graphite full-cells, while electrodes processed without the addition of Li 2 SO 4 reach 80% of their capacity after only 200 cycles. Furthermore, with regard to electrochemical performance, aqueously-processed electrodes using carbon-coated Al current collector outperform reference electrodes, based on SOTA production processes involving N -methyl-2-pyrrolidone as processing solvent and fluorinated binders. The positive impact on cycle life by the addition of Li 2 SO 4 stems from a formed sulphate coating, protecting the NCM811 surface against degradation. Results reported herein open a new avenue for the processing of Ni-rich NCM electrodes using more sustainable aqueous routes. Figure 1

High Value-Added Utilization of Waste Hydrodesulfurization Catalysts: Low-Cost Synthesis of Cathode Materials for Lithium-Ion Batteries

Repurposing Ni and Co from Alloy Scraps for the Synthesis of LiNi 0.6 Co 0.2 Mn 0.2 O 2 Cathodes

Upcycling Spent Cathode Materials to Bifunctional Catalysts for High‐Stability Lithium–Sulfur Batteries

An environmentally friendly and low-cost catalyst for Li–CO2 batteries based on Co recovered from waste lithium-ion batteries

Enhanced Electrochemical Performance of Ni-Rich Cathodes by Neutralizing Residual Lithium with Acid Compounds

A Molten-Salt Method to Synthesize Ultrahigh-Nickel Single-Crystalline LiNi0.92 Co0.06 Mn0.02 O2 with Superior Electrochemical Performance as Cathode Material for Lithium-Ion Batteries.

An Efficient Synthetic Method To Prepare High-Performance Ni-Rich Lini0.8co0.1mn0.1o2 For Lithium-Ion Batteries

Introducing an Efficient and Eco-Friendly Spray-Drying Process for the Synthesis of NCM Precursor for Lithium-ion Batteries

Simultaneous double membrane electrolysis of sodium sulfate solution and preparation of hydroxide precursor for layered cathode materials

Subtractive transformation of cathode materials in spent Li-ion batteries to a low-cobalt 5 V-class cathode material

Recovery of valuable metals and modification of cathode materials from spent lithium-ion batteries

Sonochemical synthesis of CoNi layered double hydroxide as a cathode material for assembling high performance hybrid supercapacitor

(Invited) Delineating the Intricacies Involved in the Synthesis of Cobalt-Free High-Nickel Layered Oxide Cathodes for Lithium-Ion Batteries

Resolving the Structural Defects of Spent Li 1− x CoO 2 Particles to Directly Reconstruct High Voltage Performance Cathode for Lithium‐Ion Batteries

Synthesis of LiNi0.9Co0.05Mn0.05O2 and modification with co-doping of Zr4+ and W6+ using acid leaching solution from spent lithium-ion batteries

A new defect-rich and ultrathin ZnCo layered double hydroxide/carbon nanotubes architecture to facilitate catalytic conversion of polysulfides for high-performance Li-S batteries

A Material-Oriented Metallurgical Strategy to Prepare LiNi0.8Co0.15Al0.05O2 Cathode Material from Low-Nickel Matte

Systematic Optimization of Battery Materials: Key Parameter Optimization for the Scalable Synthesis of Uniform, High-Energy, and High Stability LiNi 0.6 Mn 0.2 Co 0.2 O 2 Cathode Material for Lithium-Ion Batteries

Enabling Aqueous Processing of Ni-Rich Layered Oxide Cathode Materials by Using Lithium Sulphate as Processing Additive

Direct Upcycling of Degraded LiCoO2 Material Toward High‐Performance Single‐Crystal NCM Cathode

Stabilizing LiNi0.8Co0.1Mn0.1O2 cathode by combined moisture and HF digestion/adsorption for high-performance lithium metal batteries