Abstract:Roughly 75% of the cost for Lithium ion batteries are attributed to material cost for electrodes, electrolyte and separator. Furthermore, the production cost of the cathode material is responsible for >50% of the overall material cost. Therefore, technological breakthroughs for an increased energy density and decreased production cost along the whole battery value chain are urgently needed. State of the art (SOTA) cathode active materials (CAMs) are LiFePO 4 (LFP) and layered oxides such as LiNi 1-x-y Co x Mn y O 2 (NCM). By increasing the Ni content within NCM materials, the discharge capacity and therefore the energy density on material level can be gradually increased. Since a higher Ni content (>80% Ni) in NCM ́s implicitly entails several challenges with respect to the material synthesis procedure, stability during electrode processing as well as life time, the broad commercialization of these CAMs still needs further advances. Aqueous processing of Ni-rich layered oxide cathode materials is a promising approach to simultaneously decrease electrode manufacturing costs, while bringing environmental benefits by substituting the SOTA, often toxic and expensive organic processing solvents. Furthermore, recycling of batteries and especially of the cathode material, will probably become an important topic in the coming years. The conversion of electrodes into black mass might be cheaper and easier for aqueously-processed cathodes ( e . g ., by using fluorine-free binders). However, an aqueous environment still remains challenging due to the high reactivity of Ni-rich layered oxides towards moisture, leading to surface reconstruction, lithium leaching and Al current collector corrosion due to the resulting high pH value of the aqueous electrode paste. Common approaches to suppress current collector corrosion are the protection of the Al current collector by a carbon coating or decreasing the pH value by using dilute acids. The latter approach, especially with phosphoric acid, might lead to formation of a phosphate coating at the surface of cathode particles, which is able to protect the NCM against further degradation. Herein, we present a facile method to enable aqueous processing of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) by the addition of lithium sulphate (Li 2 SO 4 ) during electrode paste dispersion. The aqueously-processed electrodes retain 80% of their initial capacity after 400 cycles in NCM811 || graphite full-cells, while electrodes processed without the addition of Li 2 SO 4 reach 80% of their capacity after only 200 cycles. Furthermore, with regard to electrochemical performance, aqueously-processed electrodes using carbon-coated Al current collector outperform reference electrodes, based on SOTA production processes involving N -methyl-2-pyrrolidone as processing solvent and fluorinated binders. The positive impact on cycle life by the addition of Li 2 SO 4 stems from a formed sulphate coating, protecting the NCM811 surface against degradation. Results reported herein open a new avenue for the processing of Ni-rich NCM electrodes using more sustainable aqueous routes. Figure 1

Simultaneous double membrane electrolysis of sodium sulfate solution and preparation of hydroxide precursor for layered cathode materials

Ton-scale preparation of single-crystal Ni-rich ternary cathode materials for high-performance lithium ion batteries

High Value-Added Utilization of Waste Hydrodesulfurization Catalysts: Low-Cost Synthesis of Cathode Materials for Lithium-Ion Batteries

Preparation of LiNi1/3Co1/3Mn1/3O2 cathode materials from spent Li-ion batteries

Prilling and Coating Strategy to Synthesize High-Performance Spherical NaNi0.4Fe0.2Mn0.4O2 Cathode Materials for Sodium Ion Batteries

A Material-Oriented Metallurgical Strategy to Prepare LiNi0.8Co0.15Al0.05O2 Cathode Material from Low-Nickel Matte

Enabling Aqueous Processing of Ni-Rich Layered Oxide Cathode Materials by Using Lithium Sulphate as Processing Additive

A Molten-Salt Method to Synthesize Ultrahigh-Nickel Single-Crystalline LiNi0.92 Co0.06 Mn0.02 O2 with Superior Electrochemical Performance as Cathode Material for Lithium-Ion Batteries.

One-step Electrochemical In-Situ Li Doping and LiF Coating Enable Ultra-Stable Cathode for Sodium Ion Batteries

A feasible process for recycling valuable metals from LiNi0.5Co0.2Mn0.3O2 cathode materials of spent Li-ion batteries

Upcycling of spent LiMn 2 O 4 cathode towards sodium-ion battery cathode through molten salt electrolysis approach

Manipulating Stable Layered P2‐Type Cathode via a Co‐Substitution Strategy for High Performance Sodium Ion Batteries

Electrolytic Separation and Reuse of Active Materials from Discarded Lithium-Ion Batteries

Large-Scale Synthesis of the Stable Co-Free Layered Oxide Cathode by the Synergetic Contribution of Multielement Chemical Substitution for Practical Sodium-Ion Battery

A facile eutectic mixed molten salt method for synthesizing LiNi0.5Co0.2Mn0.3O2 cathode material for lithium-ion batteries

Manganese ion oxidation precipitation method for the recycling and reusing of LiNi<sub>0.8</sub>Co<sub>0.05</sub>Mn<sub>0.15</sub>O<sub>2</sub> materials for lithium-ion batteries

Na 2/3 Li 1/9 [Ni 2/9 Li 1/9 Mn 2/3 ]O 2 : A High-Performance Solid-Solution Reaction Layered Oxide Cathode Material for Sodium-Ion Batteries

Simultaneously promoting the surface/bulk structural stability of Fe/Mn-based layered cathode for sodium ion batteries

Efficient recovery and utilization of electrolytic manganese anode mud- preparation of high-performance Li1.2Ni0.2Mn0.6O2 cathode material for lithium-ion batteries

Sodium‐Rich, Co‐Ni‐Free P2‐Layered Manganese Oxide Cathodes for Sodium‐Ion Batteries

Introducing an Efficient and Eco-Friendly Spray-Drying Process for the Synthesis of NCM Precursor for Lithium-ion Batteries