Abstract:In-plane uniaxial tension of AZ31 magnesium alloy sheet with non-basal texture has been conducted in order to demonstrate the effects of loading direction on the microstructure evolution and mechanical properties at ambient temperature. Loading axes are chosen to be along five directions distributed between rolling direction (RD) and transverse direction (TD), allowing various activities in involved slip and twinning modes to take place. As for twinning modes, electron backscattered diffraction observations confirm that the contribution of \({{\{ 10\overline{1}1\} }}\) compression twinning is minimal to the plastic deformation of all deformed samples. By comparison, \({{\{ 10\overline{1}2\} }}\) extension twinning (ET) not only serves as an important carrier on sustaining and accommodating plastic strain but also contributes to the emergence of TD-component texture with the progression of plastic strain. In terms of slip modes, analysis on Schmid factor demonstrates that the increasing tilted angle between loading direction and RD of sheet is unfavorable to the activation of basal <a> slip, whereas it contributes to the activation of prismatic <a> slip. These observations consequently explain the increasing tendency of 0.2% proof yield stress. Moreover, the activations of basal <a> slip and \({{\{ 10\overline{1}2\} }}\) ET collectively contribute to the concentration of two tilted basal poles toward normal direction. With increasing angle between loading direction and RD, the activations of basal <a> slip and \({{\{ 10\overline{1}2\} }}\) ET are gradually weakened. This leads to a weakening tendency about concentration of two tilted basal poles, a generally increasing tendency about Lankford value (r-value) and a generally decreasing tendency about strain-hardening exponent (n-value).

Enhancement of the Mechanical Properties of Textured AZ31 Mg Alloy Sheets by Bimodal-Orientation Microstructure: Basal Orientation and RD-texture

Enhanced Stretch Formability of AZ31 Magnesium Alloy Sheet by Secondary Regulation of Initial Twin Orientation

Tailoring the Texture and Mechanical Properties of Textured-AZ31 Mg Alloy Sheets by Twinning and Recrystallization

Mechanical Properties and Anisotropy of AZ31 Alloy Sheet Processed by Flat Extrusion Container

Microstructure Evolution and Mechanical Behavior of AZ31 Magnesium Alloy Sheet with Bimodal Texture under Bending Deformation

Effect of texture types on microstructure evolution and mechanical properties of AZ31 magnesium alloy undergoing uniaxial tension deformation at room temperature

Effect of initial orientation on microstructure and mechanical properties of AZ31 Mg alloy sheets via accumulated extrusion bonding

Towards enhancing the ductility of AZ31 Mg alloys by controlling twin orientation at various shear strain levels

Influence of In-Plane Simple Shear Strain on the Grain Orientation Regulation and Stretch Formability of Pre-twinned AZ31 Magnesium Alloy Sheet

Influence of Bimodal Non-Basal Texture on Microstructure Characteristics, Texture Evolution and Deformation Mechanisms of AZ31 Magnesium Alloy Sheet Rolled at Liquid-Nitrogen Temperature

Multiple-twinning induced recrystallization and texture optimization in a differential-temperature-rolled AZ31B magnesium alloy with excellent ductility

Unveiling the ductility enhancement mechanisms in AZ31 magnesium alloy achieved via shear strain-assisted twin orientation regulation

Improving the Room-Temperature Bendability of Mg-3Al-1Zn Alloy Sheet by Introducing a Bimodal Microstructure and the Texture Re-Orientation

Development of Mechanical Properties in AZ31 Magnesium Alloy Processed by Cold Dynamic Extrusion

Texture Weakening of AZ31 Magnesium Alloy Sheet Obtained by a Combination of Bidirectional Cyclic Bending at Low Temperature and Static Recrystallization

Evolution of Microstructure and Mechanical Properties of AZ31 Mg Alloy Sheets Processed by Accumulated Extrusion Bonding with Different Relative Orientation

Improving Strength and Formability of Rolled AZ31 Sheet by Two-Step Twinning Deformation

Enhancement of Tensile Ductility and Stretch Formability of AZ31 Magnesium Alloy Sheet Processed by Cross-Wavy Bending

An Exceptional Ductility of AZ31 Magnesium Alloy Sheet Achieved by Consecutive Multi-Pass Cooperative Lowered-Temperature Rolling

Effects of Micro-Twin Lamellar Structure on the Mechanical Properties and Fracture Morphology of AZ31 Mg Alloy

Dependence of Microstructure Evolution and Mechanical Properties on Loading Direction for AZ31 Magnesium Alloy Sheet with Non-basal Texture During In-Plane Uniaxial Tension