Abstract:Conventional methods for hot extrusion of magnesium (Mg) alloy sheets have limitations for microstructure improvement and mechanical property enhancement. Co-extrusion of Mg alloy with an Al alloy core provides an opportunity for refining the grain size and improving basal texture. This study introduces a novel severe plastic deformation (SPD) method, Direct Extrusion-Continuous Shear (DE-CS), utilizing 6063 Al alloy as the core to fabricate innovative Mg/Al clad composite sheets. Monolithic Mg sheets (non-co-extruded condition) are extruded under identical conditions for comparison. By evaluating the microstructure and mechanical properties of AZ31 Mg alloy under co-extrusion and non-co-extrusion conditions, the positive effect of Mg-Al composite billet co-extrusion on AZ31 Mg alloy is established. The grain refinement effect in co-extruded samples is superior, enhancing plasticity without significant reduction in tensile strength. The microstructure evolution and dynamic recrystallization (DRX) behaviour of AZ31 Mg alloy during co-extrusion were analyzed comprehensively. The results indicate that, in the initial stages of deformation, various variants of {10-12} extension twins (ETs) play a crucial role in refining the original grains, forming initial [10-10]//ED fiber texture components alongside other non-basal components. Upon entering the shear deformation (SD) zone, deformed twins disappear, and small dynamically recrystallized (DRXed) grains emerge along boundaries of coarse deformation grains and within the grains. Strong shear deformations and compressive stress from transverse direction (TD) induce intensified prismatic and pyramidal slip, promoting continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX). CDRX predominantly affects elongated deformed grains, forming an [10-10]//ED fiber texture through high-energy grain boundary segmentation. Subsequently, compatible stress increases due to the activity of non-basal slip dislocation and the reduction in grain boundary (GB) size. DDRX emerges as the dominant mechanism, generating randomized [10-10]//ED fiber and non-fiber textures within parent grains and at boundaries.

An Exceptional Ductility of AZ31 Magnesium Alloy Sheet Achieved by Consecutive Multi-Pass Cooperative Lowered-Temperature Rolling

Multiple-twinning induced recrystallization and texture optimization in a differential-temperature-rolled AZ31B magnesium alloy with excellent ductility

Evolution of the Microstructure and Mechanical Properties of AZ31 Magnesium Alloy Sheets during Multi-Pass Lowered-Temperature Rolling

Significantly improvement in formability and ductility of AZ31 Mg alloy by differential temperature rolling

Ductility enhancement mechanism of AZ31 magnesium alloy with through-thickness symmetrical gradient structure prepared by hard plate rolling

Towards strength-ductility synergy through a novel technique of multi-pass lowered-temperature drawing in AZ31 magnesium alloys

Microstructure and Texture Evolution of Mg-3Zn-1Al Magnesium Alloy During Large-Strain Electroplastic Rolling

Deformation behaviour, microstructure evolution and dynamic recrystallization mechanism of AZ31 magnesium alloy under co-extruded by Mg-Al composite billet

Effect of Dual Deformation Processes on the Microstructure and Mechanical Properties of Low-Alloyed Mg-Zn-Ca-Mn Alloy

Microstructural Evolution and Mechanical Properties of Extruded AZ80 Magnesium Alloy during Room Temperature Multidirectional Forging Based on Twin Deformation Mode

Texture weakening and ductility improvement of Mg-1.1Mn-0.5Al alloy via medium temperature-high reduction rolling: twinning variants selection and dynamic recrystallization mechanism

Microstructure, Texture Evolution, and Mechanical Properties of Thin AZ31B Mg Alloy Sheets Prepared by Two-Stage Rolling

Non-basal Slips Mediated Dynamic Recrystallization Promote Synergistic Strengthening and Toughening of Centrifugal Casting Mg–1.1Mn–0.5Al Alloy via High Strain Rolling

Dynamic recrystallization and twinning behavior of magnesium alloy during hot tension

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

Enhanced mechanical properties of AZ91 magnesium alloy by asynchronously large-strain high-efficiency rolling with bimodal grain structure

Evading Strength-Ductility Tradeoff in Mg Alloy via Uniform Microstructure and Unique Texture Modification Induced by Moderate Temperature ECAP

Deformation Behavior and Microstructure Evolution of AZ31 Mg Alloy by Forging–Bending Repeated Deformation with Multi-pass Lowered Temperature

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy

Strength-ductility balance of AZ31 magnesium alloy via accumulated extrusion bonding combined with two-stage artificial cooling

Unveiling the ductility enhancement mechanisms in AZ31 magnesium alloy achieved via shear strain-assisted twin orientation regulation