Abstract:WC-Co cemented carbides are widely used in the fields of military, aerospace, mining and cutting industry etc. In this paper, a new two-step method for the preparation of WC-Co cemented carbides was proposed. First, the mixture of yellow tungsten trioxide (WO3) and cobaltic oxide (Co2O3) were reduced by carbon black to remove all the oxygen. Then, the carbothermic reduction products were precisely mixed with an appropriate amount of carbon black to directly prepare WC-Co cemented carbides. The effects of C/WO3 ratio on the phase composition, morphological evolution, particle size and mechanical properties of products are investigated. The experimental results revealed that when the C/WO3 molar ratio was above 2.7, all oxygen in the raw material mixture were removed by carbon black and a mixture of W2C and η-phase were obtained after the first step of carbothermic reduction at 1150 °C for 2 h; then, the mixture of carbothermic reduction product and an appropriate content of carbon black was compacted, and the green compact was first carbonized at 1200 °C for 2 h and then sintered at 1450 °C for 4 h to prepare cemented carbides. With the increase of C/WO3 ratio at the first stage, the content of η-phase with a low melting point increased, which resulted in the large grain size of WC in the finally prepared cemented carbide. Compared with the traditional method of preparing cemented carbides, the cemented carbides prepared by the current method showed a higher hardness and toughness. Furthermore, the addition of a proper content of the VC in the second stage can significantly inhibit the grain growth of WC and further increase the hardness of cemented carbides.

Synthesis of WC-0.67wt.%Cr<sub>3</sub>C<sub>2</sub> nanopowders by a one-step reduction-carbonization method and their characterization

Synthesis of WC-0.67wt.%Cr3C2 nanopowders by a one-step reduction-carbonization method and their characterization

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

WC-VC/Cr3C2 composite powders prepared by a carbothermic reduction-carburization process

Study on the preparation mechanism of novel WC-Cr2(C, N)-Co nanocomposites

Preparation of nano-scaled WC powder by low-temperature carbothermic reduction method

Study on influencing factors and mechanism of high-quality tungsten carbide nanopowders synthesized via carbothermal reduction

Ultrafine Binderless WC-based Cemented Carbides with Varied Amounts of AlN Nano-Powder Fabricated by Spark Plasma Sintering

Microhomogeneous WC-TiC-Co composite powders with enhanced sinterability via a two-step carburization method

Preparation and characterization of high-performance in-situ synthesized WC reinforced nickel-based coatings

Effects Of Wc Crystal Characteristics On Microstructure And Mechanical Property Of Hvof-Sprayed Wc-Cocr Coatings

Effect of carbon content on the microstructure and properties of Cr-doped WC–15Co cemented carbide

A Novel Method for Direct Synthesis of WC-Co Nanocomposite Powder

Synthesis of Y2O3-doped WC-Co powders by wet chemical method and its effect on the properties of WC-Co cemented carbide alloy

Phase Composition and Microstructure of Binderless Wc-Zrc Cemented Carbides Fabricated by Spark Plasma Sintering

Effect of Co on morphology and preparation of in situ synthesis of WC-Co composite powders

Effect of Cr3C2 Addition on Microstructure and Mechanical Properties of WC-CoNiFe Cemented Carbides

A short and facile process to synthesize WC-Co cemented carbides

Spark plasma sintered WC-Ni cemented carbides with various contents of ZrC nano-powder

Fabrication of ultrafine and nanocrystalline WC–Co mixtures by planetary milling and subsequent consolidations

Preparation and Properties of Composite Nanoceramic NiCrBSi-TiO2/WC(Co) Coatings