Abstract:The proton exchange membrane (PEM) fuel cell is considered to be one of the most promising alternative clean power generators for portable, mobile and stationary applications because of its low to zero emissions, low-temperature operation, high power density and fast start-up.Fuel (humidified hydrogen) and oxidant (humidified air) are fed into the cathode and anode, respectively. The water vapor in the cell introduced by humidification and produced by the cathode electrochemical reaction will condense to liquid water when the partial pressure of the vapor exceeds its saturation pressure. The resulting two-phase transport of water significantly affects the transport of reactants to the porous electrode and the membrane ohmic resistance, and then the cell performance. For example, liquid water accumulating in the channels and in the pores of the gas diffusion layer (GDL) increases the transport resistance of oxygen to the catalyst layer (CL), even resulting in cathode flooding at high current densities. In addition, the membrane must remain well-hydrated because the proton transport capability in the membrane is proportional to the membrane water content. Therefore, understanding and control of the water transport in the cell are important for improving cell performance. At present, the local distributions and transport of reactants in the cell are difficult to measure due to the small cell sizes; thus, numerical models (including the two-phase transport) have become an important means for understanding the reactant transport, electrochemical reactions, current density distributions, and cell performance.This work presents a complete three-dimensional, two-phase transport model for a PEM fuel cell based on the two-fluid method, in which the two-phase flow of the multi-component reactants and liquid water are coupled with the species transport, electrochemical reactions, proton and electron transport, electro-osmosis and back diffusion of water. Different two liquid water transport equations were developed for the various cell units based on the different liquid water transport mechanisms in the fuel cell. The model is used to investigate the effects of the various flow field designs in the bipolar plates on the cell performance. The improved understanding of the two-phase transport is then used to develop a series of new flow field designs, including the tapered flow field, contracted flow field, and partially blocked or blocked flow fields. The predictions show that the improved flow field designs significantly increase the liquid water removal from the GDL, which enhances the reactant transport rates and improves cell performance.

Multiple Effects of Non-Uniform Channel Width along the Cathode Flow Direction Based on a Single PEM Fuel Cell: an Experimental Investigation

Numerical Study of Cell Performance and Local Transport Phenomena in Pem Fuel Cells with Various Flow Channel Area Ratios

Development of Novel Single Fuel Cell Based on Composite Polar Plates for Highly Efficient Power Generation

All-scale investigation of a commercial proton exchange membrane fuel cell with partially narrow channels

Effect of cathode channel structure on the performance of open-cathode proton exchange membrane fuel cell in dry environments

Cross flow and distribution characteristics in automobile polymer electrolyte membrane fuel cells: A three-dimensional full-scale modeling study

Full-scale multiphase simulation of automobile PEM fuel cells with different flow field configurations

The Performance Improvement of Membrane and Electrode Assembly in Open-Cathode Proton Exchange Membrane Fuel Cell

Effects of Flow Channel Geometry on Cell Performance for Pem Fuel Cells with Parallel and Interdigitated Flow Fields

Current density and temperature distribution measurement and homogeneity analysis for a large-area proton exchange membrane fuel cell

Effect of Channel-Rib Width Ratio and Relative Humidity on Performance of a Single Serpentine PEMFC Based on Electrochemical Impedance Spectroscopy

Effects of sub-distribution zone structure of bipolar plate on the mass transport of large-area proton exchange membrane fuel cells

Numerical Analysis on Performances of Polymer Electrolyte Membrane Fuel Cells with Various Cathode Flow Channel Geometries

An experimental study of mutual effects among two‐phase flow, heat transfer, and performance in proton exchange membrane fuel cells with orientated‐type flow channels

Numerical study of the effect of relative humidity and stoichiometric flow ratio on PEM (proton exchange membrane) fuel cell performance with various channel lengths: An anode partial flooding modelling

A Simulation Study on the Optimization of Flow Channel Pattern in High Temperature Proton Exchange Membrane Fuel Cell

Optimization of variable cross-sectional flow channel parameters for fuel cells: Numerical analysis and distributional uniformity evaluation

Performance simulation and key parameters in-plane distribution analysis of a commercial-size PEMFC

Analytical and Experimental Investigations of A Proton Exchange Membrane Fuel Cell

Multi-sub-inlets at Cathode Flow-Field Plate for Current Density Homogenization and Enhancement of PEM Fuel Cells in Low Relative Humidity

Two-Phase Model Of Pem Fuel Cells For Optimal Flow Field Design Of Bipolar Plates