Abstract:Carbon nanotube/continuous carbon fiber reinforced poly(ethylene terephthalate) (CNT/CCF/PET) composites are prepared by melt impregnating. The effects of CF and CNT content on the mechanical properties, melt and crystallization behaviors, and submicroscopic morphology of CNT/CCF/PET composites are studied. The tensile test results show that the increase of CF and the addition of appropriate amount of CNT improved the tensile strength and tensile modulus of the composites. When the content of CNT is 1.0 wt% and the content of CF is 56 wt%, the properties of the composites are the best, with tensile strength of 1728.7 MPa and tensile modulus of 25.1 GPa, which is much higher than that of traditional resin matrix composites. The results of dynamic mechanical analysis (DMA) show that the storage modulus of the composites increased with the increase of CF and CNT content. In particular, the addition of CNT greatly reduced the loss modulus of the composites. Morphological analysis show that the addition of CNT improved the fiber–matrix interface of the composite, which changes from fiber pull-out and fracture failure to fiber matrix fracture failure, and the fiber matrix interface is firmly bonded. In addition, there are polymer coated CNT protrusions on the surface of the fiber was observed. The results of differential scanning calorimetry (DSC) show that the melting temperature and crystallization temperature of the composites increased with the increase of CF content. The addition of CNT had little effect on the melting temperature of the composites, but it further improved the crystallization temperature of the composites. The effect of CNT content on the crystallization kinetics of the composites is studied. The non-isothermal crystallization kinetics of the composites is described by Jeziorny's improved Avrami equation. The results show that CNT has a great influence on the crystallization type of the composites. As a nucleating agent, CNT has obvious heterogeneous nucleation effect in the composites, which improves the crystallization rate of PET.

A Holistic Evaluation of the Influence of Shear Rates and Matrix Viscosity on the Properties of Polypropylene/multi‐walled Carbon Nanotubes Composites

Sliding Behaviour of Carbon Nanothread Within a Bundle Embedded in Polymer Matrix

Comparative study on the electrical, thermal, and mechanical properties of multiwalled carbon nanotubes filled polypropylene and polyamide 6 micromoldings

Improving the electrical conductivity of multiwalled carbon nanotubes‐containing micromoldings via in situ construction of electrically conductive networks

Properties of polyphenylene sulfide/multiwalled carbon nanotubes composites: a comparison between compression molding and microinjection molding

STUDIES ON INFLUENCES OF VISCOELASTIC PROPERTIES ON MELT EXTRUSION OF CARBON NANOTUBES-FILLED ISOTACTIC POLYPROPYLENE COMPOSITES

Conductivity Insights Into the Carbon Nanotubes Mobility Restricted by the Long‐Branched Chains During the Thermal Annealing, Fast Shear Flow and Melt to Solid Cooling Process

Concurrent effect of shear flow and CNT presence on crystallization behavior and electrical properties of polypropylene based nanocomposites: A comprehensive structure-property investigation

Electrical Resistivity, Crystallization and Mechanical Properties of Polypropylene/Multi-Walled Carbon Nanotube/Calcium Carbonate Composites Prepared by Melt Mixing

Melt extrudate swell behavior of multi‐walled carbon nanotubes filled‐polypropylene composites

Effect of Carbon Nanotube on Thermal, Tribological and Mechanical Properties of 3D Printing Polyphenylene Sulfide

Improved Yield and Electrical Properties of Poly(Lactic Acid)/Carbon Nanotube Composites by Shear and Anneal

Improved Dielectric Performance of Polypropylene/ Multiwalled Carbon Nanotube Nanocomposites by Solid-Phase Orientation

Multi-walled carbon nanotube reinforcement in polypropylene nanocomposites: comprehensive analysis of thermal behavior, mechanical properties, and dispersion characteristics

Research on the thermal conductivity and mechanical properties of carbon fiber reinforced thermoplastic composites doped with different sizes carbon nanotubes: A combination of experiments, numerical simulations and multi‐objective optimization

Mechanical and Thermal Properties Modeling, Sorption Characteristics of Multiscale (Multiwalled Carbon Nanotubes/Glass Fiber) Filler Reinforced Polypropylene Composites

More Dominant Shear Flow Effect Assisted by Added Carbon Nanotubes on Crystallization Kinetics of Isotactic Polypropylene in Nanocomposites

Effect of Multi-Walled Carbon Nanotubes on the Properties of Polyoxymethylene

Mechanical Properties, Melting and Crystallization Behaviors, and Morphology of Carbon Nanotubes/Continuous Carbon Fiber Reinforced Polyethylene Terephthalate Composites

A Study on the Thermal Conductivity of Multiwalled Carbon Nanotube/Polypropylene Composite

Properties of microinjection-molded multi-walled carbon nanotubes-filled poly(lactic acid)/poly[(butylene succinate)-co-adipate] blend nanocomposites