Abstract:Carbon nanotube/continuous carbon fiber reinforced poly(ethylene terephthalate) (CNT/CCF/PET) composites are prepared by melt impregnating. The effects of CF and CNT content on the mechanical properties, melt and crystallization behaviors, and submicroscopic morphology of CNT/CCF/PET composites are studied. The tensile test results show that the increase of CF and the addition of appropriate amount of CNT improved the tensile strength and tensile modulus of the composites. When the content of CNT is 1.0 wt% and the content of CF is 56 wt%, the properties of the composites are the best, with tensile strength of 1728.7 MPa and tensile modulus of 25.1 GPa, which is much higher than that of traditional resin matrix composites. The results of dynamic mechanical analysis (DMA) show that the storage modulus of the composites increased with the increase of CF and CNT content. In particular, the addition of CNT greatly reduced the loss modulus of the composites. Morphological analysis show that the addition of CNT improved the fiber–matrix interface of the composite, which changes from fiber pull-out and fracture failure to fiber matrix fracture failure, and the fiber matrix interface is firmly bonded. In addition, there are polymer coated CNT protrusions on the surface of the fiber was observed. The results of differential scanning calorimetry (DSC) show that the melting temperature and crystallization temperature of the composites increased with the increase of CF content. The addition of CNT had little effect on the melting temperature of the composites, but it further improved the crystallization temperature of the composites. The effect of CNT content on the crystallization kinetics of the composites is studied. The non-isothermal crystallization kinetics of the composites is described by Jeziorny's improved Avrami equation. The results show that CNT has a great influence on the crystallization type of the composites. As a nucleating agent, CNT has obvious heterogeneous nucleation effect in the composites, which improves the crystallization rate of PET.

Effect of Carbon Nanotube on Thermal, Tribological and Mechanical Properties of 3D Printing Polyphenylene Sulfide

Preparation and performance study of carbon nanotube/polyphenylene sulfidecomposite materials based on floating catalytic chemical vapor deposition and continuous dusting powder

Effect of Carbon Nanotubes on the Mechanical Properties and Crystallization Behavior of Poly(ether Ether Ketone)

The effects of carbon nanotubes selective location on the structures and properties of polyphenylene sulfide/polyamide 66 fibers

A multifunctional integrated carbon nanotubes/polyphenylene sulfide composite: preparation, properties and applications

Properties of polyphenylene sulfide/multiwalled carbon nanotubes composites: a comparison between compression molding and microinjection molding

Improved bond strength, reduced porosity and enhanced mechanical properties of 3D-printed polyetherimide composites by carbon nanotubes

Mechanical behavior and microstructure of 3D-printed carbon nanotubes-reinforced Cu composite

Effect of Thermal Processing and Heat Treatment Condition on 3D Printing PPS Properties

Biobased Poly(1,3-propylene 2,5-furandicarboxylate)-Carbon Nanotubes Nanocomposites with Enhanced Thermal, Mechanical Properties and Crystallization Behavior

Friction and Wear Characteristics of Additive Manufactured CNT-Reinforced HDPE Composites in Dry Contact

Research on the thermal conductivity and mechanical properties of carbon fiber reinforced thermoplastic composites doped with different sizes carbon nanotubes: A combination of experiments, numerical simulations and multi‐objective optimization

Effects of thermal process conditions on crystallinity and mechanical properties in material extrusion additive manufacturing of discontinuous carbon fibre reinforced polyphenylene sulphide composites

3D Printing Boron Nitride Nanosheets Filled Thermoplastic Polyurethane Composites with Enhanced Mechanical and Thermal Conductive Properties

Mechanical Properties, Melting and Crystallization Behaviors, and Morphology of Carbon Nanotubes/Continuous Carbon Fiber Reinforced Polyethylene Terephthalate Composites

Comprehensive characterization of 3D-printed TPU/carbon black composites: Morphological, thermal, and mechanical properties

Highly strong carbon fibers through synergistic carbonization process of sulfonated poly( p -phenylene sulfide) and carbon nanotube

Manufacturing of Bio-Based TPU/CNT Composites Using Solvent-Free In-Situ Polymerization for 3D Printing Filament Applications

Mechanical Properties and Biocompatibility of Functionalized Carbon Nanotubes/polypropylene Composites

Investigation of electrical, electromagnetic interference shielding and tensile properties of 3D-printed acrylonitrile butadiene styrene/carbon nanotube composites

Effect of surface-treated carbon nanotubes on the mechanical and tribological performances of phenolic resin