Abstract:Abstract Here, numerous oxygen-containing functional groups were grafted onto the surface of CNTs to improve their dispersibility in an electrolyte. The CNTs were characterized by FT-IR, Raman, XPS, FE-SEM, and TEM. The results revealed that the dispersibility of the functionalized CNTs in the composites was better than unfunctionalized CNTs. CNTs/Ni composites were deposited on a copper plate by pulsed electrodeposition and ultrasonic dispersion using an electrolytic bath with CNTs concentrations from 0 to 2 g l −1 . The friction and wear behavior of the composite coatings were assessed using two different methods. In the first method, the coatings were scratched with a progressively higher load from 0–100 N, and the results demonstrate a 10 percent reduction in the coefficient of friction (COF) of the composite compared to pure nickel. The other method involved applying a constant load of 30 N, the COF and microscopic wear mechanism were investigated at different carbon nanotube contents, and the results confirmed that the COF of the composites was gradually reduced with the increase of carbon nanotube mass concentration, and the COF was only 0.343 when the carbon nanotube content was increased to 2 g l −1 . According to the XRD results, increasing the CNTs contents changed the preferred growth orientation. Moreover, the FE-SEM images of the wear surface of the 1 g l −1 CNTs/Ni sample indicated that it had the best wear resistance and showed the smoothest wear trace without apparent cracks. The addition of CNTs enhanced the wear resistance of the nickel matrix due to the superior mechanical strength and lubricating effect of the CNTs. CNTs exposed to the matrix surface reduced the direct contact between the Ni matrix and the friction pair, acted as lubricants, and reduced the wear rate.

Effect of surface-treated carbon nanotubes on the mechanical and tribological performances of phenolic resin

Effects of Carbon Nanotubes and Carbon Fiber Reinforcements on Thermal Conductivity and Ablation Properties of Carbon/phenolic Composites

Effect of Grafted Polytetrafluoroethylene Nanoparticles on the Mechanical and Tribological Performances of Phenol Resin

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Tribological Behavior of Carbon-Nanotube-Filled PTFE Composites

Tribological properties of carbon nanotube-doped carbon/carbon composites

Effect of Carbon Nanotube on Thermal, Tribological and Mechanical Properties of 3D Printing Polyphenylene Sulfide

Influence of Carbon Nanotube Coatings on Carbon Fiber by Ultrasonically Assisted Electrophoretic Deposition on Its Composite Interfacial Property.

Tribological Properties of Modified Carbon Fabric/polytetrafluoroethylene Composites

Study of the effect of amino-functionalized multiwall carbon nanotubes on dry sliding wear resistance properties of carbon fiber reinforced thermoset polymers

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Tribological Properties of Carbon Nanotube-Reinforced Composites

Tribological behaviour of surface modified carbon-fibre-reinforced polyphenylene sulphide under dry condition

Effects of the Electrophoretic Deposition of CNTs on the Mechanical Properties of Ti/CFRP Composite Laminates

Tribological properties of Ni–P-multi-walled carbon nanotubes electroless composite coating

Effects of carbon nanotube length on interfacial properties of carbon fiber reinforced thermoplastic composites

Tribological Application of Carbon Nanotubes in a Metal-Based Composite Coating and Composites

Investigation of the microstructure and tribological properties of CNTs/Ni composites prepared by electrodeposition

Mechanical and Tribological Properties of Carbon Fiber Reinforced POM Composite Filled With Maleamidic Acid Treated Carbon Nanotube

Electroless Preparation and Tribological Properties of Ni-P-Carbon Nanotube Composite Coatings under Lubricated Condition

Study of the tribological properties of carbon nanotubes filled PTFE composites