Abstract:During the fabrication of an indium-gallium-zinc oxide (IGZO) thin film transistor (TFT), the thermal process was used to reduce the resistivity of IGZO. The annealing temperature was found to have great influence on the transistor characteristics. At an optimized heat-treatment temperature, the depletion-mode IGZO TFT was fabricated with steeper subthreshold slope, higher filed-effect mobility and acceptable turn-on voltage. And the relatively conductive IGZO could directly replace the indium tin oxide as the transparent electrode of the organic light-emitting diode (OLED), reducing the mask count of the backplane for the active-matrix OLED display. INTRODUCTION Thin film transistor (TFT) based on metal oxide (MO), especially, indium-gallium-zinc oxide (IGZO), is considered as a good candidate to fabricate large area backplane for active-matrix organic light-emitting diode (AMOLED) display, due to its high mobility, good uniformity and low off-state current [1]. Our previous study [2] suggested that the resistivity (ρ) of IGZO highly depended on the heat-treatment conditions, such as annealing ambience, temperature, duration and gas permeability of IGZO cover, while the thermal process was often inevitable during the fabrication of IGZO TFT. With the active layer of IGZO covered with the gas-permeable silicon oxide (SiOx), the TFT was subjected to a serious anneals in an oxygen-deficient nitrogen (N2) ambience. With the increasing temperature, although the mobility was enhanced, the turn-on voltage (Von) became more and more negative. At an optimized temperature, the depletion-mode (DM) IGZO TFT with steeper subthreshold slope, higher filed-effect mobility and acceptable turn-on voltage was fabricated. Furthermore, such annealing-induced conductive IGZO source/drain regions can be directly used to replace the indium tin oxide (ITO) as the transparent electrode of OLED, reducing the mask count of AMOLED backplane. Annealing-Induced DM IGZO TFT Shown in Figure 1 is the evolution of the schematic cross-section of an IGZO TFT. A gate dielectric of 100 nm silicon oxide (SiOx) was first thermally grown on an n+ silicon substrate, which served as the gate electrode. 10 or 20 nm IGZO film was then room-temperature sputtered using a target of In2O3:Ga2O3:ZnO = 1:1:1 mol% in an atmosphere of 10% oxygen (O2) and 90% argon (Ar). After the patterning of the active-island using the hydrofluoric acid, a passivation layer of 300 nm SiOx was deposited at 300 oC in a plasma-enhanced chemical vapor deposition (PECVD) reactor. The tetraethylorthosilicate (TEOS) and O2 were used as the source gases. The contact holes were then opened and the resulting structure was subjected to a series of anneals, as shown in Figure 1a. Finally, 300 nm aluminum (Al) was deposited and patterned into electrodes (Fig. 1b). These TFTs were measured using an Agilent 4156C semiconductor parameter analyzer. n+ Si 100nm SiOx 300nm SiOx

Influence of Indium Tin Oxide Residues on the Electrical Performance of Hydrogenated Amorphous Silicon Thin-Film Transistors in the Backplane of Active-Matrix Displays

Influence of Indium Tin Oxide Residues on Electrical Performance of Hydrogenated Amorphous Silicon Thin Film Transistors in Backplane of Active Matrix Displays

Fabrication and performance of indium oxide based transparent thin film transistors

Effects Of Hydrogen Impurities On Performances And Electrical Reliabilities Of Indium-Gallium-Zinc Oxide Thin Film Transistors

Effects of Etching Residue on Positive Shift of Threshold Voltage in Amorphous Indium–Zinc-Oxide Thin-Film Transistors Based on Back-Channel-Etch Structure

Influence of Source and Drain Contacts on the Properties of the Indium-Zinc Oxide Thin-Film Transistors Based on Anodic Aluminum Oxide Gate Dielectrics

Impact of Deposition Temperature of the Silicon Oxide Passivation on the Performance of Indium Zinc Oxide Thin-Film Transistors

High Performance Indium‐Gallium‐Zinc Oxide Thin Film Transistor via Interface Engineering

Annealing-Induced Depletion-Mode Indium-Gallium-Zinc Oxide Thin-Film Transistor and Its Application to Active-Matrix Organic Light-Emitting Diode Display

Influence of Surface Modification of IndiumTin Oxide on Performance of Organic Light Emitting Diodes

Sol-gel Indium-Zinc-tin-oxide Thin Film Transistor Pixel Array with Superior Stabilityunder Negative Bias Illumination Stress

Influence of Source and Drain Contacts on the Properties of Indium-Gallium Zinc-Oxide Thin-Film Transistors Based on Amorphous Carbon Nanofilm As Barrier Layer

Influence of passivation deposition on the performance of In-Zn-O thin-film transistors based on etch-stopper structure

Resilience of Fluorinated Indium-Gallium-Zinc Oxide Thin-Film Transistor Against Hydrogen-Induced Degradation

Impact of electrode materials on the performance of amorphous IGZO thin-film transistors

Suppression of the Short-Channel Effect in Dehydrogenated Elevated-Metal Metal- Oxide (EMMO) Thin-Film Transistors

Effects of Hf Incorporation on Indium Zinc Oxide Thin-Film Transistors Using Solution Process

Effect of Electrical Performance and Reliability by Adjustment of the Sequence and Concentration of HfAlOx on IWO Thin-Film Transistors

Comparative Study on Hydrogen Behavior in InGaZnO Thin Film Transistors with a SiO2/SiNx/SiO2 Buffer on Polyimide and Glass Substrates

Effect of ITO Serving As a Barrier Layer for Cu Electrodes on Performance of A-Igzo TFT

24.3: Short‐Channel Indium‐Gallium‐Zinc Oxide Thin‐Film Transistor Enabled by Thermal Dehydrogenation and Oxidizing Defect‐Suppression