Abstract:Thermoelectric materials with high average power factor and thermoelectric figure of merit (ZT) has been a sought-after goal. Here, we report new n-type thermoelectric system CuxPbSe0.99Te0.01 (x = 0.0025, 0.004, and 0.005) exhibiting record-high average ZT ∼ 1.3 over 400–773 K ever reported for n-type polycrystalline materials including the state-of-the-art PbTe. We concurrently alloy Te to the PbSe lattice and introduce excess Cu to its interstitial voids. Their resulting strong attraction facilitates charge transfer from Cu atoms to the crystal matrix significantly. It follows the increased carrier concentration without damaging its mobility and the consequently improved electrical conductivity. This interaction also increases effective mass of electron in the conduction band according to DFT calculations, thereby raising the magnitude of Seebeck coefficient without diminishing electrical conductivity. Resultantly, Cu0.005PbSe0.99Te0.01 attains an exceptionally high average power factor of ∼27 μW cm–1 K–2 from 400 to 773 K with a maximum of ∼30 μW cm–1 K–2 at 300 K, the highest among all n- and p-type PbSe-based materials. Its ∼23 μW cm–1 K–2 at 773 K is even higher than ∼21 μW cm–1 K–2 of the state-of-the-art n-type PbTe. Interstitial Cu atoms induce the formation of coherent nanostructures. They are highly mobile, displacing Pb atoms from the ideal octahedral center and severely distorting the local microstructure. This significantly depresses lattice thermal conductivity to ∼0.2 Wm–1 K–1 at 773 K below the theoretical lower bound. The multiple effects of the dual incorporation of Cu and Te synergistically boosts a ZT of Cu0.005PbSe0.99Te0.01 to ∼1.7 at 773 K.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/jacs.0c07712?goto=supporting-info">https://pubs.acs.org/doi/10.1021/jacs.0c07712</a>.Details in theoretical calculations, additional APT results, and thermoelectric properties (<a class="ext-link" href="/doi/suppl/10.1021/jacs.0c07712/suppl_file/ja0c07712_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Breaking the Sodium Solubility Limit for Extraordinary Thermoelectric Performance in P-Type PbTe

Breaking sodium solubility limit for extraordinary thermoelectric performance in p-type PbTe

Promoted Na Solubility and Modified Band Structure for Achieving Exceptional Average ZT by Extra Mn Doping in PbTe.

Engineering atomic-level crystal lattice and electronic band structure for extraordinarily high average thermoelectric figure of merit in n-type PbSe

Manipulating Pb Vacancies Achieved Ultra‐High Thermoelectrics in Quaternary Pb0.95Na0.04Te1‐xSex via Fine‐Tuning Se Solubility

Multiple valence bands convergence and strong phonon scattering lead to high thermoelectric performance in p-type PbSe

Atomic Level Defect Structure Engineering for Unusually High Average Thermoelectric Figure of Merit in N‐type PbSe Rivalling PbTe

Realization of Valence Band Convergence for High Thermoelectric Performance P-Type PbS

Improved Solubility in Metavalently Bonded Solid Leads to Band Alignment, Ultralow Thermal Conductivity, and High Thermoelectric Performance in SnTe

Achieving higher thermoelectric performance of n-type PbTe by adjusting band structure and enhanced phonons scattering

Realizing high-ranged thermoelectric performance in PbSnS2 crystals

Band convergence and nanostructure modulations lead to high thermoelectric performance in SnPb0.04Te-y% AgSbTe2

Extraordinary role of Zn in enhancing thermoelectric performance of Ga-doped n-type PbTe

Enhanced Thermoelectric Performance of N‐Type PbSe Through Semi‐Coherent Nanostructure by AgCuTe Alloying

Thermoelectric enhancement for n-type PbS via synergistic effect of Ti doping and Cu2S compositing

Enhanced Thermoelectric Performance in N-Type Polycrystalline SnSe by PbBr2 Doping

Enhanced thermoelectric performance of n-type Nb-doped PbTe by compensating resonant level and inducing atomic disorder

Exceptionally High Average Power Factor and Thermoelectric Figure of Merit in n-type PbSe by the Dual Incorporation of Cu and Te

Enhancing Thermoelectric Performance in P-Type Sb2Te3-Based Compounds Through Nb─Ag Co-Doping with Donor-Like Effect.

Enhanced Thermoelectric Performance of N-Type PbTe Through the Introduction of Low-Dimensional C60 Nanodots

Band Engineering Through Pb‐Doping of Nanocrystal Building Blocks to Enhance Thermoelectric Performance in Cu3SbSe4