Abstract:Thermoelectric materials with high average power factor and thermoelectric figure of merit (ZT) has been a sought-after goal. Here, we report new n-type thermoelectric system CuxPbSe0.99Te0.01 (x = 0.0025, 0.004, and 0.005) exhibiting record-high average ZT ∼ 1.3 over 400–773 K ever reported for n-type polycrystalline materials including the state-of-the-art PbTe. We concurrently alloy Te to the PbSe lattice and introduce excess Cu to its interstitial voids. Their resulting strong attraction facilitates charge transfer from Cu atoms to the crystal matrix significantly. It follows the increased carrier concentration without damaging its mobility and the consequently improved electrical conductivity. This interaction also increases effective mass of electron in the conduction band according to DFT calculations, thereby raising the magnitude of Seebeck coefficient without diminishing electrical conductivity. Resultantly, Cu0.005PbSe0.99Te0.01 attains an exceptionally high average power factor of ∼27 μW cm–1 K–2 from 400 to 773 K with a maximum of ∼30 μW cm–1 K–2 at 300 K, the highest among all n- and p-type PbSe-based materials. Its ∼23 μW cm–1 K–2 at 773 K is even higher than ∼21 μW cm–1 K–2 of the state-of-the-art n-type PbTe. Interstitial Cu atoms induce the formation of coherent nanostructures. They are highly mobile, displacing Pb atoms from the ideal octahedral center and severely distorting the local microstructure. This significantly depresses lattice thermal conductivity to ∼0.2 Wm–1 K–1 at 773 K below the theoretical lower bound. The multiple effects of the dual incorporation of Cu and Te synergistically boosts a ZT of Cu0.005PbSe0.99Te0.01 to ∼1.7 at 773 K.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/jacs.0c07712?goto=supporting-info">https://pubs.acs.org/doi/10.1021/jacs.0c07712</a>.Details in theoretical calculations, additional APT results, and thermoelectric properties (<a class="ext-link" href="/doi/suppl/10.1021/jacs.0c07712/suppl_file/ja0c07712_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Exceptionally High Average Power Factor and Thermoelectric Figure of Merit in n-type PbSe by the Dual Incorporation of Cu and Te

Engineering atomic-level crystal lattice and electronic band structure for extraordinarily high average thermoelectric figure of merit in n-type PbSe

Atomic Level Defect Structure Engineering for Unusually High Average Thermoelectric Figure of Merit in N‐type PbSe Rivalling PbTe

Enhanced Thermoelectric Performance of N‐Type PbSe Through Semi‐Coherent Nanostructure by AgCuTe Alloying

Realizing Ultrahigh Thermoelectric Performance in n‐Type PbSe Through Lattice Planification and Introducing Liquid‐Like Cu Ions

Enhanced Average Power Factor and ZT Value in PbSe Thermoelectric Material with Dual Interstitial Doping

High-Ranged <i>ZT</i> Value Promotes Thermoelectric Cooling and Power Generation in n-Type PbTe

Realizing High Thermoelectric Performance in P-Type SnSe Through Crystal Structure Modification

Pseudo‐Nanostructuring and Grain Refinement Enhance the Near‐Room‐Temperature Thermoelectric Performance in n‐type PbSe

Engineering an Atomic-Level Crystal Lattice and Electronic Band Structure for an Extraordinarily High Average Thermoelectric Figure of Merit in N-Type PbSe

Synergistically optimizing interdependent thermoelectric parameters of n-type PbSe through introducing a small amount of Zn

Complex lattice occupation of copper leading to enhanced thermoelectric performance in n-type PbSe

Enhancing Thermoelectric Performance of p-Type PbSe through Suppressing Electronic Thermal Transports

Remarkable Roles of Cu to Synergistically Optimize Phonon and Carrier Transport in N-Type PbTe-Cu2Te

Lattice Plainification Leads to High Thermoelectric Performance of P-Type PbSe Crystals

Rational Electronic and Structural Designs Advance BiCuSeO Thermoelectrics

Multiple valence bands convergence and strong phonon scattering lead to high thermoelectric performance in p-type PbSe

Achieving high thermoelectric performance with Pb and Zn codoped polycrystalline SnSe via phase separation and nanostructuring strategies

High Thermoelectric Performance of Cu-Doped PbSe-PbS System Enabled by High-Throughput Experimental Screening

Achieving higher thermoelectric performance of n-type PbTe by adjusting band structure and enhanced phonons scattering

Lattice expansion enables interstitial doping to achieve a high average ZT in n‐type PbS