Abstract:Nb-Si base alloys have attracted considerable attentions as the potential high temperature structural materials working in the service temperature range of 1200 similar to 1400 degrees C because of their high melting points (>1750 degrees C), moderate densities (6.6 similar to 7.2 g/cm(3)) and excellent high temperature strength. However, the mismatching between room temperature fracture toughness and high temperature strength has limited their practical applications. Directional solidification (DS) and alloying have been proved to be the effective methods to overcome this critical issue. The DS processes used to prepare Nb-Si base alloys included Czochralski directional solidification in a copper crucible, electron beam directional solidification, optical floating zone melting, integrally directional solidification and electromagnetic cold crucible directional solidification (ECCDS). The previous studies focused on the effect of process parameters on microstructure and mechanical properties in the steady-state growth region (SSGR). However, the microstructure in the SSGR was controlled by the solid-liquid interface, and the solid-liquid interface was controlled by process parameters. Therefore, the study about the effect of process parameters on solid-liquid interface was very important. In this work, the master alloy with the nominal composition of Nb-22Ti-16Si-3Cr-3Al-2Hf (atomic fraction, %) was prepared by vaccum non-consumable arc-melting first, and then induction skull melting. The DS experiments were performed in the ECCDS device equipped with a square water cooled copper crucible (internal dimension; 26 mmx26 mmx120 mm) and a Ga-In alloy pool. There were three processing parameters in ECCDS including heating power of power supply, withdrawal rate and holding time. The DS ingots were prepared according to the orthogonal test (L-9(3(3))). Instability degree was defined as the ratio of the height of solid-liquid interface to the width of the DS ingot. The results showed that there were three macroscopic morphologies of solid-liquid interfaces; the increase of holding time, decrease of withdrawal rate and elevation of heating power were conducive to keeping the solid-liquid interface macroscopic morphology planar. With the increase of withdrawal rate, primary dendrite arm spacing. (d(1)) and secondary dendrite arm spacing (d(2)) decreased gradually; with the increase of heating power, d(1) and d(2) increased gradually; with the increase of holding time, d(1) and d(2) increased first and then decreased. The higher withdrawal rate, lower heating power and less holding time were beneficial to refining the d(1) and d(2).

Anisotropy of Mechanical Properties in Directionally Solidified Nb-Si Alloys at Room Temperature Compression

Microstructure and Properties of Directionally Solidified NbSi<sub>2</sub>/ Nb<sub>5</sub>Si<sub>3</sub> Composites

Microstructure and Properties of Directionally Solidified NbSi<sub>2</sub>/ Nb<sub>5</sub>Si<sub>3</sub> Composites

MICROSTRUCTURAL CHARACTERISTICS AND MECHANICAL PROPERTIES OF A Nb/Nb5Si3 BASED COMPOSITE WITH AND WITHOUT DIRECTIONAL SOLIDIFICATION

Mechanism of Solute Hardening and Dislocation Debris-Mediated Ductilization in Nb-Si Alloy

Microstructure Evolution and Mechanical Properties of a Directionally Solidified Nb-Ti-Si-Cr-Al-Hf-Dy Alloy

Temperature Effects on Deformation Substructures and Mechanisms of a Ni-based Single Crystal Superalloy

Orientation dependence of microstructure deformation mechanism and tensile mechanical properties of Nickel-based single crystal superalloys: A molecular dynamics simulation

Microstructure and Nanomechanical Behavior of Individual Phase in Β-Solidifying Ti-43Al-5Nb-3.5Cr-1Zr Alloy

Behaviors and interactions of strengthening and constraint for ductile Nbss matrix in Nb–Si based alloys

Orientation and temperature dependence of yielding and deformation behavior of a nickel-base single crystal superalloy

Anisotropic Mechanical Behavior and Microstructural Characteristics of AA2099-T83 Alloy Sheet: Experiment and Simulation

Phase transformation and dislocation behavior dependence on cooling rate in novel refractory high entropy alloy

Investigations on the Solidification Microstructures and Room Temperature Compression Properties of Nb-doped NiAl-32Cr-6Mo Hypereutectic Alloy

Lattice Rotation and Deformation Mechanisms under Tensile Loading in a Single-Crystal Superalloy with [001] Misorientation

Mechanical Anisotropy of Laser Powder Bed Fusion Fabricated Ti-41Nb Alloy Using Pre-Alloyed Powder: Roles Played by Grain Morphology and Crystallographic Orientation

Effect of Deformation Parameters on Microstructure Evolution, Flow Softening Behavior and Nanoindentation Properties of Nb–24Ti–16Si–2Al–4Fe–5V Alloy

Microstructural and mechanical characterization of Nb-based in situ composites from Nb–Si–Ti ternary system

Ternary eutectic growth and associated tensile properties of directionally solidified Al87Si11Ni2 alloy

Effect of Processing Parameters on Solid-Liquid Interface of Nb-Si Base Alloy Fabricated by Electromagnetic Cold Crucible Directional Solidification

Anisotropy of Mechanical Properties in Directionally Solidified Nb-Si Alloys at Room Temperature Compression

Microstructure and Properties of Directionally Solidified NbSi<sub>2</sub>/ Nb<sub>5</sub>Si<sub>3</sub> Composites

Microstructure and Properties of Directionally Solidified NbSi&lt;sub&gt;2&lt;/sub&gt;/ Nb&lt;sub&gt;5&lt;/sub&gt;Si&lt;sub&gt;3&lt;/sub&gt; Composites

MICROSTRUCTURAL CHARACTERISTICS AND MECHANICAL PROPERTIES OF A Nb/Nb5Si3 BASED COMPOSITE WITH AND WITHOUT DIRECTIONAL SOLIDIFICATION

Mechanism of Solute Hardening and Dislocation Debris-Mediated Ductilization in Nb-Si Alloy

Microstructure Evolution and Mechanical Properties of a Directionally Solidified Nb-Ti-Si-Cr-Al-Hf-Dy Alloy

Temperature Effects on Deformation Substructures and Mechanisms of a Ni-based Single Crystal Superalloy

Orientation dependence of microstructure deformation mechanism and tensile mechanical properties of Nickel-based single crystal superalloys: A molecular dynamics simulation

Microstructure and Nanomechanical Behavior of Individual Phase in Β-Solidifying Ti-43Al-5Nb-3.5Cr-1Zr Alloy

Behaviors and interactions of strengthening and constraint for ductile Nbss matrix in Nb–Si based alloys

Orientation and temperature dependence of yielding and deformation behavior of a nickel-base single crystal superalloy

Anisotropic Mechanical Behavior and Microstructural Characteristics of AA2099-T83 Alloy Sheet: Experiment and Simulation

Phase transformation and dislocation behavior dependence on cooling rate in novel refractory high entropy alloy

Investigations on the Solidification Microstructures and Room Temperature Compression Properties of Nb-doped NiAl-32Cr-6Mo Hypereutectic Alloy

Lattice Rotation and Deformation Mechanisms under Tensile Loading in a Single-Crystal Superalloy with [001] Misorientation

Mechanical Anisotropy of Laser Powder Bed Fusion Fabricated Ti-41Nb Alloy Using Pre-Alloyed Powder: Roles Played by Grain Morphology and Crystallographic Orientation

Effect of Deformation Parameters on Microstructure Evolution, Flow Softening Behavior and Nanoindentation Properties of Nb–24Ti–16Si–2Al–4Fe–5V Alloy

Microstructural and mechanical characterization of Nb-based in situ composites from Nb–Si–Ti ternary system

Ternary eutectic growth and associated tensile properties of directionally solidified Al87Si11Ni2 alloy

Effect of Processing Parameters on Solid-Liquid Interface of Nb-Si Base Alloy Fabricated by Electromagnetic Cold Crucible Directional Solidification

Microstructure and Properties of Directionally Solidified NbSi<sub>2</sub>/ Nb<sub>5</sub>Si<sub>3</sub> Composites