Abstract:In order to reveal the relationship between microstructure inhomogeneity and mechanical anisotropy, the Al–Cu–Li alloy 100 mm thick plate for aerospace was evaluated. The grain structure, crystallographic texture, phase structure and fractography of different thickness positions and directions were observed by optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). The in-plane and through-thickness anisotropy were characterized by tensile properties, fracture toughness and hardness tests. The results demonstrate a greater in-plane anisotropy in yield strength at the same thickness position of the plate. The Brass texture component increases successively at T, T/4, and T/2 positions, while the Cu texture component exhibits minimal variation. The in-plane anisotropy mainly arises from the Brass texture. Through-thickness anisotropy in the same direction is primarily influenced by the diameter, number density, and volume fraction of the T1 strengthening phase. The average diameter and number density of the primary strengthening phase T1 within grains are highest at the T/2 position and lowest at the T position. The plate contains unrecrystallized, elongated pancake-like grains along the rolling direction. Fracture toughness tests conducted in the L-T and T-L directions predominantly reveal dimple-type transgranular shear fractures, while the S-L direction exhibits intergranular fracture as the primary characteristic. The crack divider delamination toughening mechanism is the main contributor to higher fracture toughness values in the L-T and T-L directions compared to those in the S-L direction. The results reveal the corresponding relationship between the microstructure inhomogeneity and the mechanical anisotropy of Al–Li alloy ultra-thick plates, and provide ideas for the adjustment of process parameters during processing deformation and the regulation of microstructure during heat treatment of large-scale Al–Li alloy thick plates, which has engineering application reference value.

Anisotropic Mechanical Behavior and Microstructural Characteristics of AA2099-T83 Alloy Sheet: Experiment and Simulation

Strengthening Contribution of Precipitates and Anisotropy of Yield Strength in Al-Li Alloys 2090 and 2090+Ce

Effect of Initial Orientation on the Anisotropy in Microstructure and Mechanical Properties of 2195 Al-Li Alloy Sheet during Hot Tensile Deformation

Anisotropic Tensile Behavior and Related Yield Point Phenomena in Annealed Ultrafine-Grained Pure Aluminum

Atomic Simulation of the Effect of Orientation on Tensile/compressive Properties in Nickel-Based Single Crystal Superalloys

The experimental study on plastic flow and anisotropic properties of the new generation Aluminum Lithium alloy sheet

Anisotropy of 1420 Al-Li Alloy Cold-rolled Sheet

On Anisotropic Tensile Mechanical Behavior of Al–Cu–Li AA2198 Alloy under Different Ageing Conditions

Anisotropy in creep-aging behavior of Al–Li alloy under different stress levels: experimental and constitutive modeling

Anisotropic Behavior and Temperature-Dependent Mechanical Properties of Aa1060 Aluminum Alloy: A Comprehensive Microstructural Study

Effect of microstructural inhomogeneity on mechanical anisotropy of Al–Cu–Li alloy plate

Influence of microstructural and crystallographic inhomogeneity on tensile anisotropy in thick-section Al-Li-Cu-Mg plates

In-Plane Anisotropy of 1545 Aluminum Alloy Sheet

Anisotropy in Mechanical Properties During Microscale Uniaxial Tensile Deformation of Cu/Ni Clad Foils

Characterization and constitutive analysis-based crystal plasticity of warm flow and fracture behaviours of 2060 Al-Cu-Li alloy

Study on the Anisotropy of 2195 Al-Li Alloy

Microstructure evolution and mechanical properties of Al-Cu-Li alloys with different rolling schedules and subsequent artificial ageing heat treatment

Mechanical Properties and Anisotropy of AZ31 Alloy Sheet Processed by Flat Extrusion Container

Effects of microstructure on tensile properties of AA2050-T84 Al-Li alloy

Study on Anisotropy of Al-Zn-Mg-Sc-Zr Alloy Sheet

Investigation on Anisotropic Mechanical Behavior of Ti-6Al-4V Alloy Via Schmid Factor and Kernel Average Misorientation Distribution