Abstract:Scandium is very expensive and limits the application potential of Sc containing alloys. A novel high-strength Al–Mg–Mn-Sc-Zr alloy was designed for reducing Sc. Multiple strengthening mechanisms were utilized for designing this alloy, especially for the solid solution strengthening which benefits from ultrahigh cooling. With the addition of Mn and Si, the strength of our alloy reaches comparable level of similar alloys while the Sc content is 40–60 % less than them. The effect of Mn addition on microstructure and mechanical properties were carefully studied. Near full-dense samples with relative density >99.88 % were obtained with the help of overlapping prediction model. The continuous Mg2Si network was observed with Si introduction and broken up with increasing Mn content. According to the tensile experiment results and corresponding calculations, it was considered that the thermal stability and the effect of precipitate strengthening was slightly deteriorated. However, obvious improvement of the tensile strength was observed with increasing Mn addition, and the ductility maintains in a certain range. After aging at 280 °C for 4 h, the sample of 1.4 wt% Mn exhibits the highest ultimate strength of 497.08 ± 7.22 MPa, and possesses a considerable ductility of 8.01 ± 0.34 %. The Portevin-Le Chatelier (PLC) effect was observed in stress-strain curves, which reflects a dynamic strain aging of mobile dislocations and solute atoms. After aging, the stress amplitude and waiting time of serration flow decrease obviously, because of the introduction of bypassing precipitates and reduction of diffusion time. Compared with other similar alloys, our alloy exhibited comparable yield strength and elongation, but considerable advantages in material costs resulting from lower Sc content. It will offer not only an idea for alloy design utilizing the ultra-high solid solubility of elements, but also a feasible way to further expand application field of high-strength Al-based alloys through reducing the material costs.

Synergistic Effect of Mn + Sc Additions on the Microstructure Evolution and Mechanical Properties of Mg-Gd-Y-Mn-Sc Alloy

Preparation of high-performance Mg-Gd-Y-Mn-Sc alloy by heat treatment and extrusion

Effect of Mn and Sc on Microstructures and Mechanical Properties of Mg-9Gd-4Y Alloy

Microstructure evolution, mechanical property response and strengthening mechanism induced by compositional effects in Al–6 Mg alloys

Simultaneous improvement of strength and ductility by Mn addition in extruded Mg–Gd–Zn alloy

Microstructures and Mechanical Properties of Mg-Sc Binary Alloy

Effects of Mn Addition on the Microstructures and Mechanical Properties of the Mg-15Gd-1Zn Alloy

The Effect of Mn Content on a Novel Al–Mg–Si-Sc-Zr Alloy Produced by Laser Powder Bed Fusion: the Microstructure and Mechanical Behavior

Enhancing Strength and Creep Resistance of Mg–Gd–Y–Zn–Zr Alloy by Substituting Mn for Zr

Synergic Effects of Gd and Y Contents on the Age-Hardening Response and Elevated-Temperature Mechanical Properties of Extruded Mg–Gd(-Y)-Zn-Mn Alloys

Effects of the Simultaneous Addition of Gd and Mn on the Microstructures and Mechanical Properties of Mg-Bi Alloys

Effect of Minor Gd Addition on Microstructure Evolution and Properties of As-cast Mg-8Zn-1Mn-3Sn Alloy

Effect of Y and Gd solutes on grain refinement of the as-extruded Mg-Gd(-Y)-Zn-Mn alloys

Effects of Mg and Sc Additions on the Microstructure, Mechanical Properties, and Thermal Stability of a Cast Al-2Li-2Cu-0.2Zr Alloy after Thermal Exposure

Microstructure and Mechanical Properties of Extruded Mg–Gd–Y–Zn Alloy with Mn or Zr Addition

Effect of Sc microalloying on microstructure evolution and mechanical properties of extruded Al-Zn-Mg-Cu alloys

Microstructures and Properties of Al–Zn–Mg–Mn Alloy with Trace Amounts of Sc and Zr

Effects of Mn Addition on the Microstructure and Mechanical Properties of Cast Mg–9Al–2Sn (wt.%) Alloy

Synergistic Effect of Sc and Excess Mg on the Microstructure and Mechanical Properties of Hypoeutectic Al-10Mg2Si Alloy

Tailoring the corrosion behavior and mechanism of Mg-Gd-Zn alloys via Sc microalloying

Improvement of Mechanical Properties of Hot Extruded and Aged Mg-Zn-Mn-Sn Alloy Through Dy Addition