Abstract:The growing need for sustainable and low-carbon energy sources has led to significant research in alternative fuels. The majority of energy produced today comes from fossil fuels, which has led to enormous emissions of greenhouse gases. The direct combustion of fossil fuels produces syngas and hydrogen, which contribute to global warming. In contrast, the gasification process of biomass produces clean energy in the form of syngas and hydrogen. The biomass and plastic co-gasification has gained a lot of attention recently due to the challenges associated with gasifying biomass and plastic wastes separately. The broader objectives of this study are to alleviate these waste management problems and optimize the syngas LHV and H 2 content using co-gasification process. The synthesis gas is a crucial intermediary used to create chemicals and fuels for transportation. The hydrogen component of synthesis gas can also be utilized directly as fuel for hydrogen fuel cells, which produce electricity. This work employs Aspen simulator to analyze an optimum processing condition where the synthesis gas has the maximum feasible hydrogen content and calorific value which has not been investigated in the available literature so far. Aspen software is used in this study since it can be useful in figuring out reaction yield and performing parametric studies to optimize process conditions. It is found that the carbon dioxide emission sharply decreases as the proportion of plastic increases in co-gasification. The mole fractions of CO, H 2 and CO 2 that the current model predicts using experimental data on rice husk have average modeling errors of less than 8%, indicating a satisfactory fit with the experimental findings. Under 1 bar of pressure and a combined feed rate of 100 kg/h for both plastic and biomass, the simulation was run at temperatures between 550 °C and 1300 °C. When steam was added, the fraction of hydrogen increased by approximately a factor of two for a steam-to-biomass ratio (SBR) of 2. Following the addition of plastic to the feed, the amount of hydrogen in the produced gas rose for all temperatures. When 15% plastic is combined with the feed at 850 °C, carbon dioxide is reduced by roughly 60%. The results indicate significant increase in calorific value of the product as well as the hydrogen proportion—suggesting plastic addition as an excellent method to improve the LHV of biomass gasification.

Hydrogen-rich Syngas Production by Gasification of Urea-formaldehyde Plastics in Supercritical Water

Exploration on the steam gasification mechanism of waste PE plastics based on ReaxFF-MD and DFT methods

Supercritical water co-gasification of waste R134a and plastics to produce valuable chemicals and fuels: ReaxFF reactive molecular dynamic simulation

Supercritical water Co-gasification of biomass and plastic wastes for hydrogen-rich gas production using Ni-Cu/AC-CaO catalyst

Assessment of Supercritical Water Gasification of Food Waste under the Background of Waste Sorting: Influences of Plastic Waste Contents

Hydrogen production from plastic waste: A comprehensive simulation and machine learning study

Investigation of hydrogen production via waste plastic gasification in a fluidized bed reactor using aspen plus

Syngas and hydrogen production from co-gasification of rice husk biomass and plastic waste mixture using Aspen Plus

Hydrothermal Liquefaction of Plastics: a survey of the effect of reaction conditions on the reaction efficiency.

Defossilization and decarbonization of hydrogen production using plastic waste: Temperature and feedstock effects during thermolysis stage

Hydrogen‐Rich Syngas Production by DC Thermal Plasma Steam Gasification from Biomass and Plastic Mixtures

Production of hydrogen-rich fuel gas from waste plastics using continuous plasma pyrolysis reactor

Three-stage pyrolysis–steam reforming–water gas shift processing of household, commercial and industrial waste plastics for hydrogen production

Assessment of Sewage Sludge Gasification in Supercritical Water for H-2-rich Syngas Production

Hydrogen Production by Three-Stage (i) Pyrolysis, (ii) Catalytic Steam Reforming, and (iii) Water Gas Shift Processing of Waste Plastic

Production of H2-rich Syngas from Gasification of Unsorted Food Waste in Supercritical Water

Insights into hydro thermal gasification process of microplastic polyethylene via reactive molecular dynamics simulations

High-purity H2 Production from Mixed PVC/PET Plastic Wastes Through Tandem Hydrothermal Depolymerization and Aqueous Phase Reforming

Analysis of hydrogen production potential from waste plastics by pyrolysis and in line oxidative steam reforming

An Investigation of a Hybrid Plasma Gasification System for Various Waste Plastics Thermochemical Degradation in the Fuel Extraction Process

Product Characterization of Hydrothermal Liquefaction and Supercritical Water Gasification of Water Hyacinth