Abstract:The growing need for sustainable and low-carbon energy sources has led to significant research in alternative fuels. The majority of energy produced today comes from fossil fuels, which has led to enormous emissions of greenhouse gases. The direct combustion of fossil fuels produces syngas and hydrogen, which contribute to global warming. In contrast, the gasification process of biomass produces clean energy in the form of syngas and hydrogen. The biomass and plastic co-gasification has gained a lot of attention recently due to the challenges associated with gasifying biomass and plastic wastes separately. The broader objectives of this study are to alleviate these waste management problems and optimize the syngas LHV and H 2 content using co-gasification process. The synthesis gas is a crucial intermediary used to create chemicals and fuels for transportation. The hydrogen component of synthesis gas can also be utilized directly as fuel for hydrogen fuel cells, which produce electricity. This work employs Aspen simulator to analyze an optimum processing condition where the synthesis gas has the maximum feasible hydrogen content and calorific value which has not been investigated in the available literature so far. Aspen software is used in this study since it can be useful in figuring out reaction yield and performing parametric studies to optimize process conditions. It is found that the carbon dioxide emission sharply decreases as the proportion of plastic increases in co-gasification. The mole fractions of CO, H 2 and CO 2 that the current model predicts using experimental data on rice husk have average modeling errors of less than 8%, indicating a satisfactory fit with the experimental findings. Under 1 bar of pressure and a combined feed rate of 100 kg/h for both plastic and biomass, the simulation was run at temperatures between 550 °C and 1300 °C. When steam was added, the fraction of hydrogen increased by approximately a factor of two for a steam-to-biomass ratio (SBR) of 2. Following the addition of plastic to the feed, the amount of hydrogen in the produced gas rose for all temperatures. When 15% plastic is combined with the feed at 850 °C, carbon dioxide is reduced by roughly 60%. The results indicate significant increase in calorific value of the product as well as the hydrogen proportion—suggesting plastic addition as an excellent method to improve the LHV of biomass gasification.

Syngas and hydrogen production from co-gasification of rice husk biomass and plastic waste mixture using Aspen Plus

Simulation of biomass-plastic co-gasification in a fluidized bed reactor using Aspen plus

Energy, efficiency, and environmental analysis of hydrogen generation via plasma co-gasification of biomass and plastics based on parameter simulation using Aspen plus

Co-gasification of biomass and polyethylene: a simulation study by considering tar formation

Investigation of hydrogen production via waste plastic gasification in a fluidized bed reactor using aspen plus

Product Compositions from Sequential Biomass Pyrolysis and Gasification of Its Char Residue

Optimizing the operating conditions for hydrogen-rich syngas production in a plasma co-gasification process of municipal solid waste and coal using Aspen Plus

Optimizing Hydrogen-Rich Biofuel Production: Syngas Generation from Wood Chips and Corn Cobs

Hydrogen production via integrated configuration of steam gasification process of biomass and water‐gas shift reaction: Process simulation and optimization

Process Simulation for Rice Husk Staging Pyrolysis and Gasification With Steam

On the operating parameters for hydrogen-rich syngas production in a plasma co-gasification process of municipal solid wastes and polypropylene using a constrained model in Aspen plus

Co-gasification of rice husk and plastic in the presence of CaO using a novel ANN model-incorporated Aspen plus simulation

Hydrogen production via gasification of corn stover: modeling and simulation using Aspen Plus®

Comparative assessment on thermo-chemical conversion of different waste plastics to value added syngas: thermodynamic investigation

Supercritical water Co-gasification of biomass and plastic wastes for hydrogen-rich gas production using Ni-Cu/AC-CaO catalyst

Hydrogen production from plastic waste: A comprehensive simulation and machine learning study

Numerical simulation analysis of biomass gasification and rich-H2 production process in a downdraft gasifier

Hydrogen/Methane Production from Supercritical Water Gasification of Lignite Coal with Plastic Waste Blends

Development of integrated reactive system based on co-combustion of wood biomass and plastic: Efficient hydrogen and methane production

Process modelling and thermodynamic performance optimization of biomass air gasification fuelled with waste poultry litter pellet by integrating Aspen plus with RSM

Recent Development of Biomass and Plastic Co-Pyrolysis for Syngas Production